- 您現在的位置：買賣IC網 > PDF目錄30753 > LM4842MHX/NOPB (NATIONAL SEMICONDUCTOR CORP) 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | LM4842MHX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 13/31頁 |
| 文件大?。?/td> | 1306K |
| 代理商： | LM4842MHX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Application Information (Continued)
(7)
As an example when using a speaker with a low frequency
limit of 150Hz, the input coupling capacitor using Equation
(7), is 0.053F. The 0.33F input coupling capacitor shown
in Figure 1 allows the LM4842 to drive high efficiency, full
range speaker whose response extends below 30Hz.
TURN ON Characteristics
The LM4842 contains advanced circuitry that minimizes
turn-on and shutdown transients or “clicks and pops”. For
this discussion, turn-on refers to either applying the power
supply voltage or when the shutdown mode is deactivated.
While the power supply is ramping to its final value, the
LM4842’s internal amplifiers are configured as unity gain
buffers. An internal current source changes the voltage of
the BYPASS pin in a controlled, linear manner. Ideally, the
input and outputs track the voltage applied to the BYPASS
pin. The gain of the internal amplifiers remains unity until the
voltage on the BYPASS pin reaches 1/2 V
DD. As soon as the
voltage on the BYPASS pin is stable, the LM4842 is ready to
be fully turned on. To turn the device on, the input signal
must exceed 22mV
rms.
This is accomplished through a
threshold detect circuit that enables all appropriate output
amplifiers after the 22mVrms limit is reached. Until this
threshold is reached, some of the amplifiers remain in a
tri-state mode. This insures that there is no current flowing
through to the speakers or headphones during power up.
Without current flow, the speakers or headphones remain
silent. During headphone mode, A+, B-, and B+ are in tri-
state mode during power up. During speaker mode, A+ and
B+ are in tri-state mode during power up.
Although the BYPASS pin current cannot be modified,
changing the size of C
BYPASS alters the device’s turn-on
time. As the size of C
BYPASS increases, the turn-on time
increases. There is a linear relationship between the size of
C
BYPASS and the turn-on time. Here are some typical turn-on
times for various values of C
BYPASS:
C
BYPASS
T
ON
0.01F
2ms
0.1F
20ms
0.22F
44ms
0.47F
94ms
1.0F
200ms
DOCKING STATION INTERFACE
Applications such as notebook computers can take advan-
tage of a docking station to connect to external devices such
as monitors or audio/visual equipment that sends or receives
line level signals. The LM4842 has two outputs, Dock A and
Dock B, which connect to outputs of the internal input am-
plifiers that drive the volume control inputs. These input
amplifiers can drive loads of >1k
(such as powered speak-
ers) with a rail-to-rail signal. Since the output signal present
on the Dock A and Dock B pins are biased to V
DD/2, coupling
capacitors should be connected in series with the load when
using these outputs. Typical values for the output coupling
capacitors are 0.33F to 1.0F. If polarized coupling capaci-
tors are used, connect their ’+’ terminals to the respective
output pin.
Since the Dock outputs precede the internal volume control,
the signal amplitude will be equal to the input signal’s mag-
nitude and cannot be adjusted. However, the input amplifi-
er’s closed-loop gain can be adjusted using external resis-
tors. These 20k resistors (R
FA and RFB) are shown in Figure
2 and they set each input amplifier’s gain to -1. Use Equation
7 to determine the input and feedback resistor values for a
desired gain.
-A
v =RF /RIN
(8)
Adjusting the input amplifier’s gain sets the minimum gain for
that channel. Although the single ended output of the Bridge
Output Amplifiers can be used to drive line level outputs, it is
recommended that the A & B Dock Outputs simpler signal
path be used for better performance.
MUX CONTROL AND MODE PINS
The LM4842 has two pairs of stereo inputs. The MUX CON-
TROL pin determines which of these stereo pairs of inputs
are active. Applying 0V to the MUX CONTROL pin (with the
Mode pin tied low) selects inputs A0 and B0. Applying V
DD to
the MUX CONTROL (with the Mode pin tied low) pin selects
inputs A1 and B1 (See Truth Table for Logic Inputs).
When the Mode pin is pulled high the MUX Control is dis-
abled and the Headphone Sense Pin controls the A and B
input pairs as follows:
Headphone Sense enabled (Headphone plugged in) se-
lects inputs A1 and B1.
Headphone Sense disabled (Headphone not plugged in)
selects inputs A0 and B0.
When the MODE pin is high the HP SENSE controls the
MUX inputs. This configuration can be very useful, for ex-
ample, when the headphone acoustic output needs to be
much lower than the BTL Speaker Output. Two different
gains can be hardwired into the two pairs of MUX input
circuits. This allows the user to have the HP SENSE auto-
matically change the output level for either of the MUX input
pairs by switching between the two pairs of MUX inputs, if
the same input signal is connected to both MUX inputs.
When the MODE pin is low the MUX pin switches the MUX
input pairs directly.
BEEP DETECT FUNCTION
Computers and notebooks produce a system ’beep’ signal
that drives a small speaker. The speaker’s auditory output
signifies that the system requires user attention or input. To
accommodate this system alert signal, the LM4842’s beep
input pin is a mono input that accepts the beep signal.
Internal level detection circuitry at this input monitors the
beep signal’s magnitude. When a signal level greater than
V
DD/2 is detected on the BEEP IN pin, the bridge output
amplifiers are enabled. The beep signal is amplified and
applied to the load connected to the output amplifiers. A valid
beep signal will be applied to the load even when MUTE is
active. Use the input resistors connected between the BEEP
IN pin and the stereo input pins to accommodate different
beep signal amplitudes. These resistors are shown as
200k
devices in Figure 1. Use higher value resistors to
reduce the gain applied to the beep signal. The resistors
must be used to pass the beep signal to the stereo inputs.
LM4842
www.national.com
20
相關PDF資料 |
PDF描述 |
|---|---|
| LM4842MTX/NOPB | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| LM4843MH/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO20 |
| LM4843MHX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO20 |
| LM4850MM/NOPB | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4850MT/NOPB | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4842MT | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Amplifiers with DC Volume Control Transient Free Outputs, and Cap-less Headphone Drive |
| LM4842MT/NOPB | 功能描述:IC AMP AUDIO PWR 2.2W AB 28TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4843 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Audio Power Amplifiers with DC Volume Control |
| LM4843MH | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Audio Power Amplifiers with DC Volume Control |
| LM4843MHX | 功能描述:IC AMP AUDIO PWR 2.2W AB 20TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。