- 您現在的位置：買賣IC網 > PDF目錄30753 > LM4842MTX/NOPB (NATIONAL SEMICONDUCTOR CORP) 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 PDF資料下載
參數資料
| 型號： | LM4842MTX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻控制 |
| 英文描述： | 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO28 |
| 封裝： | TSSOP-28 |
| 文件頁數： | 17/31頁 |
| 文件大小： | 1306K |
| 代理商： | LM4842MTX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Audio Power Amplifier Design
AUDIO AMPLIFIER DESIGN: DRIVING 1W INTO AN 8
LOAD
The following are the desired operational parameters:
Power Output:
1 W
RMS
Load Impedance:
8
Input Level:
1 V
RMS
Input Impedance:
20 k
Bandwidth:
100 Hz20 kHz ± 0.25 dB
The design begins by specifying the minimum supply voltage
necessary to obtain the specified output power. One way to
find the minimum supply voltage is to use the Output Power
vs Supply Voltage curve in the Typical Performance Char-
acteristics section. Another way, using Equation (9), is to
calculate the peak output voltage necessary to achieve the
desired output power for a given load impedance. To ac-
count for the amplifier’s dropout voltage, two additional volt-
ages, based on the Dropout Voltage vs Supply Voltage in the
Typical Performance Characteristics curves, must be
added to the result obtained by Equation (9). The result is
Equation (10).
(9)
V
DD
≥ (V
OUTPEAK+(VODTOP +VODBOT))
(10)
The Output Power vs Supply Voltage graph for an 8
load
indicates a minimum supply voltage of 4.6V. This is easily
met by the commonly used 5V supply voltage. The additional
voltage creates the benefit of headroom, allowing the
LM4842 to produce peak output power in excess of 1W
without clipping or other audible distortion. The choice of
supply voltage must also not create a situation that violates
of maximum power dissipation as explained above in the
Power Dissipation section.
After satisfying the LM4842’s power dissipation require-
ments, the minimum differential gain needed to achieve 1W
dissipation in an 8
load is found using Equation (11).
(11)
Thus, a minimum overall gain of 2.83 allows the LM4842’s to
reach full output swing and maintain low noise and THD+N
performance.
The last step in this design example is setting the amplifier’s
3dB frequency bandwidth. To achieve the desired ±0.25dB
pass band magnitude variation limit, the low frequency re-
sponse must extend to at least one-fifth the lower bandwidth
limit and the high frequency response must extend to at least
five times the upper bandwidth limit. The gain variation for
both response limits is 0.17dB, well within the ±0.25dB
desired limit. The results are an
f
L = 100Hz/5 = 20Hz
(12)
and an
f
H = 20kHz x 5 = 100kHz
(13)
As mentioned in the Selecting Proper External Compo-
nents section, R
i (Right & Left) and Ci (Right & Left) create
a highpass filter that sets the amplifier’s lower bandpass
frequency limit. Find the coupling capacitor’s value using
Equation (14).
C
i
≥ 1/(2πR
ifL)
(14)
The result is
1/(2
π*20k*20Hz) = 0.397F
(15)
Use a 0.39F capacitor, the closest standard value.
The product of the desired high frequency cutoff (100kHz in
this example) and the differential gain A
VD, determines the
upper passband response limit. With A
VD = 3 and fH =
100kHz, the closed-loop gain bandwidth product (GBWP) is
300kHz. This is less than the LM4842’s 3.5MHz GBWP. With
this margin, the amplifier can be used in designs that require
more differential gain while avoiding performance,restricting
bandwidth limitations.
Recommended Printed Circuit
Board Layout
Figures 7 through 9 show the recommended 2 later PC
board layout that is optimized for the MT/MH packaged
LM4842 and associated external components. Figures 10
through 12 show the recommended 2 layer PC board layout
that is optimized for the LQ packaged LM4842 and associ-
ated external components. These circuits are designed for
use with an external 5V supply and 4
or 8 speakers.
These circuit boards are easy to use. Apply 5V and ground to
the board’s V
DD and GND pads, respectively. Connect 4
or
8
speakers between the board’s OUTA and +OUTA and
OUTB and +OUTB pads.
LM4842
www.national.com
24
相關PDF資料 |
PDF描述 |
|---|---|
| LM4843MH/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO20 |
| LM4843MHX/NOPB | 2 CHANNEL(S), VOLUME CONTROL CIRCUIT, PDSO20 |
| LM4850MM/NOPB | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| LM4850MT/NOPB | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4850LD/NOPB | 0.3 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4843 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Audio Power Amplifiers with DC Volume Control |
| LM4843MH | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 2W Audio Power Amplifiers with DC Volume Control |
| LM4843MHX | 功能描述:IC AMP AUDIO PWR 2.2W AB 20TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4844 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4844_07 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 1.2W Audio Sub-System with 3D Enhancement |
發布緊急采購，3分鐘左右您將得到回復。