參數資料
型號： LM4852ITL/NOPB
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 音頻／視頻放大
英文描述： 1.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PBGA18
封裝： MICRO SMD-18
文件頁數： 7/21頁
文件大小： 860K
代理商： LM4852ITL/NOPB
Application Information (Continued)
TABLE 3. Volume Control
V4
V3
V2
V1
V0
Gain (dB)
G
00000
-40.5
00001
-39.0
00010
-37.5
00011
-36.0
00100
-34.5
00101
-33.0
00110
-31.5
00111
-30.0
01000
-28.5
01001
-27.0
01010
-25.5
01011
-24.0
01100
-22.5
01101
-21.0
01110
-19.5
01111
-18.0
10000
-16.5
10001
-15.0
10010
-13.5
10011
-12.0
10100
-10.5
10101
-9.0
10110
-7.5
10111
-6.0
11000
-4.5
11001
-3.0
11010
-1.5
11011
0.0
11100
1.5
11101
3.0
11110
4.5
11111
6.0
EXPOSED-DAP MOUNTING CONSIDERATIONS
The LM4852’s exposed-DAP (die attach paddle) package
(LD) provides a low thermal resistance between the die and
the PCB to which the part is mounted and soldered. This
allows rapid heat transfer from the die to the surrounding
PCB copper area heatsink, copper traces, ground plane, and
finally, surrounding air. The result is a low voltage audio
power amplifier that produces 1.1W dissipation in a 8
load
at
≤ 1% THD+N. This high power is achieved through careful
consideration of necessary thermal design. Failing to opti-
mize thermal design may compromise the LM4852’s high
power performance and activate unwanted, though neces-
sary, thermal shutdown protection.
The LD package must have its DAP soldered to a copper
pad on the PCB. The DAP’s PCB copper pad is then, ideally,
connected to a large plane of continuous unbroken copper.
This plane forms a thermal mass, heat sink, and radiation
area. Place the heat sink area on either outside plane in the
case of a two-sided or multi-layer PCB. (The heat sink area
can also be placed on an inner layer of a multi-layer board.
The thermal resistance, however, will be higher.) Connect
the DAP copper pad to the inner layer or backside copper
heat sink area with 6 (3 X 2) (LD) vias. The via diameter
should be 0.012in - 0.013in with a 1.27mm pitch. Ensure
efficient thermal conductivity by plugging and tenting the vias
with plating and solder mask, respectively.
Best thermal performance is achieved with the largest prac-
tical copper heat sink area. If the heatsink and amplifier
share the same PCB layer, a nominal 2.5in
2 (min) area is
necessary for 5V operation with a 4
load. Heatsink areas
not placed on the same PCB layer as the LM4852 should be
5in
2 (min) for the same supply voltage and load resistance.
The last two area recommendations apply for 25C ambient
temperature. Increase the area to compensate for ambient
temperatures above 25C. In all circumstances and under all
conditions, the junction temperature must be held below
LM4852
www.national.com
15
相關PDF資料
PDF描述
LM4854MT/NOPB 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
LM4854MTX/NOPB 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
LM4854LD/NOPB 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
LM4854LDX/NOPB 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14
LM4856LQ/NOPB 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24
相關代理商/技術參數
參數描述
LM4852ITLX/NOPB 功能描述:IC AMP AUDIO PWR 1.5W AB 18USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4852LQ 制造商:Texas Instruments 功能描述:1W MONO 100MW STEREO SUBSYST 4852
LM4852LQ/NOPB 功能描述:IC AMP AUDIO PWR 1.5W MONO 24LLP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR)
LM4852LQBD 功能描述:BOARD EVALUATION LM4852LQ RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:Boomer® 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
LM4853 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Mono 1.5 W / Stereo 300mW Power Amplifier
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*