- 您現在的位置：買賣IC網 > PDF目錄30753 > LM4854MT/NOPB (NATIONAL SEMICONDUCTOR CORP) 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 PDF資料下載
參數資料
| 型號： | LM4854MT/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| 封裝： | TSSOP-14 |
| 文件頁數： | 15/29頁 |
| 文件大?。?/td> | 1440K |
| 代理商： | LM4854MT/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Application Information (Continued)
Figure 4 shows an optional resistor connected between the
amplifier output that drives the headphone jack sleeve and
ground. This resistor provides a ground path that supressed
power supply hum. This hum may occur in applications such
as notebook computers in a shutdown condition and con-
nected to an external powered speaker. The resistor’s 100
value is a suggested starting point. Its final value must be
determined based on the tradeoff between the amount of
noise suppression that may be needed and minimizing the
additional current drawn by the resistor (25mA for a 100
resistor and a 5V supply).
Single-Ended Output Power Performance and Measure-
ment Considerations
The LM4854 delivers clean, low distortion SE output power
into loads that are greater than 10
. As an example, output
power for 16
and 32 loads are shown in the Typical
Performance Characteristic curves. For loads less than 10
,
the LM4854 can typically supply 180mW of low distortion
power. However, when higher dissipation is desired in loads
less than 10
, a dramatic increase in THD+N may occur.
This is normal operation and does not indicate that proper
functionality has ceased. When a jump from moderate to
excessively high distortion is seen, simply reducing the out-
put voltage swing will restore the clean, low distortion SE
operation.
The dramatic jump in distortion for loads less than 10
occurs when current limiting circuitry activates. During SE
operation, AMP2 (refer to Figure 2) drives the headphone
sleeve. An on-board circuit monitors this amplifier’s output
current. The sudden increase in THD+N is caused by the
current limit circuitry forcing AMP2 into a high-impedance
output mode. When this occurs, the output waveform has
discontinuities that produce large amounts of distortion. It
has been observed that as the output power is steadily
increased, the distortion may jump from 5% to greater than
35%. Indeed, 10% THD+N may not actually be achievable.
ESD Protection
As stated in the Absolute Maximum Ratings, the AMP2
output pin has a maximum ESD susceptibility rating of
8000V. For higher ESD voltages, the addition of a PCDN042
dual transil (from California Micro Devices), as shown in
Figure 4, will provide additional protection.
SELECTING EXTERNAL COMPONENTS
Input Capacitor Value Selection
Amplifying the lowest audio frequencies requires high value
input coupling capacitor (Ci in Figure 2). A high value capaci-
tor can be expensive and may compromise space efficiency
in portable designs. In many cases, however, the speakers
used in portable systems, whether internal or external, have
little ability to reproduce signals below 150Hz. Applications
using speakers with this limited frequency response reap
little improvement by using large input capacitor.
The LM4854’s advanced output transient suppression cir-
cuitry has eliminated the need to select the input capacitor’s
value in relation to the BYPASS capacitor’s value as was
necessary in some previous Boomer amplifiers. The value of
CI is now strictly determined by the desired low frequency
response.
As shown in Figure 2, the input resistor (R
i) and the input
capacitor (C
i) produce a high pass filter cutoff frequency that
is found using Equation (7).
f
c =1/(2
πR
iCi)
(7)
As an example when using a speaker with a low frequency
limit of 150Hz, C
i, using Equation (7) is 0.063F. The 1.0F
C
i shown in Figure 2 allows the LM4854 to drive high effi-
ciency, full range speaker whose response extends below
30Hz.
Bypass Capacitor Value Selection
Besides minimizing the input capacitor size, careful consid-
eration should be paid to value of CB, the capacitor con-
nected to the BYPASS pin. Since C
B determines how fast
the LM4854 settles to quiescent operation, its value is critical
when minimizing turn-on pops. The slower the LM4854’s
outputs ramp to their quiescent DC voltage (nominally V
DD/
2), the smaller the turn-on pop. Choosing C
B equal to 1.0F
along with a small value of Ci (in the range of 0.1F to
0.39F), produces a click-less and pop-less shutdown func-
tion. As discussed above, choosing C
i no larger than neces-
sary for the desired bandwidth helps minimize clicks and
pops. CB’s value should be in the range of 5 times to 7 times
the value of C
i. This ensures that output transients are
eliminated when power is first applied or the LM4854 re-
sumes operation after shutdown.
20038212
FIGURE 3. Headphone Circuit
200382E8
FIGURE 4. The PCDN042 provides additional ESD
protection beyond the 8000V shown in the Absolute
Maximum Ratings for the AMP2 output
LM4854
www.national.com
22
相關PDF資料 |
PDF描述 |
|---|---|
| LM4854MTX/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4854LD/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4854LDX/NOPB | 0.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO14 |
| LM4856LQ/NOPB | 1.5 W, 3 CHANNEL, AUDIO AMPLIFIER, QCC24 |
| LM4856ITL/NOPB | 1.1 W, 3 CHANNEL, AUDIO AMPLIFIER, PBGA18 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4854MTX/NOPB | 功能描述:IC AMP AUDIO PWR 2.3W AB 14TSSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4855 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Boomer AUDIO POWER AMPLIFIER Integrated Audio Amplifier System |
| LM48555 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ceramic Speaker Driver |
| LM48555TL | 制造商:Texas Instruments 功能描述:Audio Amp Speaker 1-CH Mono Class-AB 12-Pin uSMD T/R 制造商:Texas Instruments 功能描述:IC AMP POWER AUDIO SMD |
| LM48555TL/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。