- 您現在的位置：買賣IC網 > PDF目錄384600 > LM4858MM (NATIONAL SEMICONDUCTOR CORP) Mono 1.5 W / Stereo 300mW Power Amplifier PDF資料下載
參數資料
| 型號： | LM4858MM |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | Mono 1.5 W / Stereo 300mW Power Amplifier |
| 中文描述： | 1.5 W, 2 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
| 封裝： | 0.118 INCH, 0.50 MM PITCH, MSOP-10 |
| 文件頁數： | 13/17頁 |
| 文件大小： | 683K |
| 代理商： | LM4858MM |
Application Information
(Continued)
The LM4858’s unity-gain stability allows a designer to maxi-
mize system performance. The LM4858’s gain should be set
no higher than necessary for any given application. A low
gain configuration maximizes signal-to-noise performance
and minimizes THD+N. However, a low gain configuration
also requires large input signals to obtain a given output
power. Input signals equal to or greater than 1V
are
available from sources such as audio codecs. Please refer to
the section,
Audio Power Amplifier Design
, for a more
complete explanation of proper gain selection.
Selecting Input and Output Capacitor Values
Besides gain, one of the major considerations is the closed-
loop bandwidth of the amplifier. To a large extent, the band-
width is dictated by the choice of external components
shown in
Figure 1
. The input coupling capacitor C
and
resistor R
form a first order high pass filter that limits low
frequency response. C
’s value should be based on the
desired frequency response weighed against the following:
Large value input and output capacitors are both expensive
and space consuming for portable designs. Clearly a certain
sized capacitor is needed to couple in low frequencies with-
out severe attenuation. But in many cases the speakers
used in portable systems, whether internal or external, have
little ability to reproduce signals below 150Hz. Thus, large
value input and output capacitors may not increase system
performance.
AUDIO POWER AMPLIFIER DESIGN
Design a 1W / 8
Bridged Audio Amplifier
Given:
Power Output:
Load Impedance
Input Level:
Input Impedance:
Bandwidth:
1W
RMS
8
1V
RMS
20k
100Hz - 20kHz
±
0.25dB
A designer must first determine the minimum supply voltage
needed to obtain the specified output power. By extrapolat-
ing from the Output Power vs Supply Voltage graphs in the
Typical Performance Characteristics
section, the supply
rail can be easily found. A second way to determine the
minimum supply rail is to calculate the required V
using Equation 5 and add the dropout voltage. This results in
Equation 6, where V
and V
are extrapolated
from the Dropout Voltage vs Supply Voltage curve in the
Typical Performance Characteristics
section.
(5)
V
DD
≥
(V
OPEAK
+ (V
ODTOP
+ V
ODBOT
))
(6)
Using the Output Power vs Supply Voltage graph for an 8
load, the minimum supply rail is 4.7V. But since 5V is a
standard supply voltage in most applications, it is chosen for
the supply rail. Extra supply voltage creates headroom that
allows the LM4858 to reproduce peaks in excess of 1W
without producing audible distortion. However, the designer
must make sure that the chosen power supply voltage and
output load does not violate the conditions explained in the
Power Dissipation
section.
Once the power dissipation equations have been addressed,
the required differential gain can be determined from Equa-
tion 7.
(7)
R
F
/ R
I
= A
VD
/ 2
(8)
From Equation 6, the minimum A
VD
is 2.83; use A
VD
= 3.
The desired input impedance was 20k
, and with an A
VD
of
3, using Equation 8 results in an allocation of R
I
= 20k
and
R
F
= 30k
.
The final design step is to set the amplifier’s 3dB frequency
bandwidth. To achieve the desired
±
0.25dB pass band
magnitude variation limit, the low frequency response must
extend to at least onefifth the lower bandwidth limit and the
high frequency response must extend o at least five times
the upper bandwidth limit. The variation for both response
limits is 0.17dB, well within the
±
0.25dB desired limit. This
results in:
f
L
= 100Hz / 5 = 20Hz
f
H
= 20kHz x 5 = 100kHz
As stated in the
External Components
section, R
in con-
junction with C
create a highpass filter. Find the coupling
capacitor’s value using Equation 9.
C
I
≥
1 / (2
π
R
I
f
L
)
(9)
C
I
≥
1 / ( 2
π
x 20k
x 20Hz) = 0.397μF
Use a 0.39μF capacitor, the closest standard value.
The high frequency pole is determined by the product of the
desired high frequency pole, f
, and the differential gain,
A
. With A
= 3 and f
= 100kHz, the resulting GBWP =
150kHz which is much smaller than the LM4858 GBWP of
10MHz. This difference indicates that a designer can still use
the LM4858 at higher differential gains without bandwidth
limitations.
PCB LAYOUT AND SUPPLY REGULATION
CONSIDERATIONS FOR DRIVING 3
AND 4
LOADS
Power dissipated by a load is a function of the voltage swing
across the load and the load’s impedance. As load imped-
ance decreases, load dissipation becomes increasingly de-
pendant on the interconnect (PCB trace and wire) resistance
between the amplifier output pins and the load’s connec-
tions. Residual trace resistance causes a voltage drop,
which results in power dissipated in the trace and not in the
load as desired. For example, 0.1
trace resistance reduces
the output power dissipated by a 4
load from 2.0W to
1.95W. This problem of decreased load dissipation is exac-
erbated as load impedance decreases. Therefore, to main-
tain the highest load dissipation and widest output voltage
swing, PCB traces that connect the output pins to a load
must be as wide as possible.
Poor power supply regulation adversely affects maximum
output power. A poorly regulated supply’s output voltage
L
www.national.com
13
相關PDF資料 |
PDF描述 |
|---|---|
| LM4858 | Mono 1.5 W / Stereo 300mW Power Amplifier |
| LM4858LD | Mono 1.5 W / Stereo 300mW Power Amplifier |
| LM4888SQ | Dual 2.1W Audio Amplifier Plus Stereo Headphone & 3D Enhancement |
| LM4888 | Dual 2.1W Audio Amplifier Plus Stereo Headphone & 3D Enhancement |
| LM4898LD | 1 Watt Fully Differential Audio Power Amplifier With Shutdown Select |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4858MM/NOPB | 功能描述:IC AMP AUDIO PWR 1.9W AB 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4859 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4859_05 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Stereo 1.2W Audio Sub-system with 3D Enhancement |
| LM4859SP | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| LM4859SP/NOPB | 功能描述:音頻放大器 RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。