- 您現在的位置：買賣IC網 > PDF目錄30755 > LM4892MX/NOPB (NATIONAL SEMICONDUCTOR CORP) 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 PDF資料下載
參數資料
| 型號： | LM4892MX/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 17/22頁 |
| 文件大?。?/td> | 1037K |
| 代理商： | LM4892MX/NOPB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁
Electrical Characteristics V
The following specifications apply for V
DD = 3.3V, AV = 2, and 8
load unless otherwise specified. Limits apply for T
A =
25C. (Continued)
Symbol
Parameter
Conditions
LM4892
Units
(Limits)
Typical
Limit
PSSR
Power Supply Rejection Ratio
V
ripple = 200mV sine p-p
60(f = 217Hz)
62 (f = 1kHz)
dB
Electrical Characteristics V
DD = 2.6V
(Notes 1, 2)
The following specifications apply for V
DD = 2.6V, AV = 2, and 8
load unless otherwise specified. Limits apply for T
A = 25C.
Symbol
Parameter
Conditions
LM4892
Units
(Limits)
Typical
Limit
I
DD
Quiescent Power Supply Current
V
IN = 0V, Io = 0A, HP sense = 0V
2.6
mA (max)
V
IN = 0V, Io = 0A, HP sense = 2.6V
1.5
mA (max)
I
SD
Shutdown Current
Vshutdown = GND (Note 8)
0.1
A (max)
P
o
Output Power
THD = 1% (max), f = 1kHz,
R
L =8
, HP Sense < 0.8V
0.25
W
THD = 1% (max), f = 1kHz,
R
L =4
, HP Sense < 0.8V
0.28
W
THD = 1% (max), f = 1kHz, R
L =
32
, HP Sense > 2.5V
20
mW
V
IH
HP Sense high input voltage
2.0
V (min)
V
IL
HP Sense low input voltage
0.8
V (max)
THD+N
Total Harmonic Distortion+Noise
P
o = 0.1 Wrms; f = 1kHz 10Hz
≤
BW
≤ 80kHz
0.1
%
PSSR
Power Supply Rejection Ratio
V
ripple = 200mV sine p-p
44(f = 217Hz)
44 (f = 1kHz)
dB
Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature TA. The maximum
allowable power dissipation is PDMAX =(TJMAX–TA)/θJA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4892, see power derating
currents for additional information.
Note 4: Human body model, 100pF discharged through a 1.5k
resistor.
Note 5: Machine Model, 220pF–240pF discharged through all pins.
Note 6: Typicals are measured at 25C and represent the parametric norm.
Note 7: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase ISD by a maximum of 2A.
Note 9: The Exposed-DAP of the LDA10B package should be electrically connected to GND or an electrically isolated copper area. The LM4892LD demo board
(views featured in the Application Information section) has the Exposed-DAP connected to GND with a PCB area of 353mils x 86.7mils (8.97mm x 2.20mm) on
the copper top layer and 714.7mils x 368mils (18.15mm x 9.35mm) on the copper bottom layer.
External Components Description
(Figure 1)
Components
Functional Description
1.
R
i
Inverting input resistance which sets the closed-loop gain in conjunction with R
f. This resistor also forms a
high pass filter with C
i at fC= 1/(2
π R
iCi).
2.
C
i
Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a
highpass filter with R
i at fc = 1/(2
π R
iCi). Refer to the section, Proper Selection of External Components,
for an explanation of how to determine the value of C
i.
3.
R
f
Feedback resistance which sets the closed-loop gain in conjunction with R
i.
LM4892
www.national.com
4
相關PDF資料 |
PDF描述 |
|---|---|
| LM4892M/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4892MMX/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4892MM/NOPB | 1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4893M | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO8 |
| LM4893MM/NOPB | 1.1 W, 1 CHANNEL, AUDIO AMPLIFIER, PDSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM4893 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.1 Watt Audio Power Amplifier |
| LM4893ITL | 制造商:Texas Instruments 功能描述:AMP POWER AUDIO 1.1W SMD BUMP-9 |
| LM4893ITL/NOPB | 功能描述:IC AMP AUDIO PWR 1.1W MONO 9USMD RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:DirectDrive® 類型:H 類 輸出類型:耳機，2-通道（立體聲） 在某負載時最大輸出功率 x 通道數量:35mW x 2 @ 16 歐姆 電源電壓:1.62 V ~ 1.98 V 特點:I²C，麥克風，靜音，短路保護，音量控制 安裝類型:表面貼裝 供應商設備封裝:25-WLP（2.09x2.09） 封裝/外殼:25-WFBGA，WLCSP 包裝:帶卷 (TR) |
| LM4893ITLBD | 功能描述:BOARD EVALUATION LM4893ITL RoHS:否 類別:編程器，開發系統 >> 評估板 - 音頻放大器 系列:Boomer® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LM4893ITLX | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:1.1 Watt Audio Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。