參數資料
型號： LM75ADP
廠商： NXP Semiconductors N.V.
元件分類： 工業控制
英文描述： Digital temperature sensor and thermal watchdog
封裝： LM75AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 17, 2005,;LM75AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 17, 2005,;LM
文件頁數： 11/24頁
文件大?。?/td> 137K
代理商： LM75ADP
LM75A_4
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 04 — 10 July 2007
11 of 24
NXP Semiconductors
LM75A
Digital temperature sensor and thermal watchdog
When the power supply voltage is dropped below the device power-on reset level of
approximately 1.9 V (POR) and then rises up again, the device will be reset to its default
condition as listed above.
7.10 Protocols for writing and reading the registers
The communication between the host and the LM75A must strictly follow the rules as
defined by the I
2
C-bus management. The protocols for LM75A register read/write
operations are illustrated in
Figure 5
to
Figure 10
together with the following definitions:
1. Before a communication, the I
2
C-bus must be free or not busy. It means that the SCL
and SDA lines must both be released by all devices on the bus, and they become
HIGH by the bus pull-up resistors.
2. The host must provide SCL clock pulses necessary for the communication. Data is
transferred in a sequence of 9 SCL clock pulses for every 8-bit data byte followed by
1-bit status of the acknowledgement.
3. During data transfer, except the START and STOP signals, the SDA signal must be
stable while the SCL signal is HIGH. It means that the SDA signal can be changed
only during the LOW duration of the SCL line.
4. S: START signal, initiated by the host to start a communication, the SDA goes from
HIGH to LOW while the SCL is HIGH.
5. RS: RE-START signal, same as the START signal, to start a read command that
follows a write command.
6. P: STOP signal, generated by the host to stop a communication, the SDA goes from
LOW to HIGH while the SCL is HIGH. The bus becomes free thereafter.
7. W: write bit, when the write/read bit = LOW in a write command.
8. R: read bit, when the write/read bit = HIGH in a read command.
9. A: device acknowledge bit, returned by the LM75A. It is LOW if the device works
properly and HIGH if not. The host must release the SDA line during this period in
order to give the device the control on the SDA line.
10. A’: master acknowledge bit, not returned by the device, but set by the master or host
in reading 2-byte data. During this clock period, the host must set the SDA line to
LOW in order to notify the device that the first byte has been read for the device to
provide the second byte onto the bus.
11. NA: Not Acknowledge bit. During this clock period, both the device and host release
the SDA line at the end of a data transfer, the host is then enabled to generate the
STOP signal.
12. In a write protocol, data is sent from the host to the device and the host controls the
SDA line, except during the clock period when the device sends the device
acknowledgement signal to the bus.
13. In a read protocol, data is sent to the bus by the device and the host must release the
SDA line during the time that the device is providing data onto the bus and controlling
the SDA line, except during the clock period when the master sends the master
acknowledgement signal to the bus.
相關PDF資料
PDF描述
LM75AD Digital temperature sensor and thermal watchdog
LM75ADP Digital temperature sensor and thermal watchdog
LM75AD Digital temperature sensor and thermal watchdog
LM75BD Digital temperature sensor and thermal watchdog
LM75BDP Digital temperature sensor and thermal watchdog
相關代理商/技術參數
參數描述
LM75ADP,118 功能描述:板上安裝溫度傳感器 TEMP SENSOR DIGITAL RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM75ADP,118 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, 0.125C, 3C, TSSOP-8
LM75ADP,118-CUT TAPE 制造商:NXP 功能描述:LM75A Series SMD 5.5 mA Digital Temperature Sensor w/ Thermal Watchdog TSSOP-8
LM75ADP/DG,118 功能描述:板上安裝溫度傳感器 DIGITAL TEMP SENSOR AND THERMAL WATCHDOG RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM75ADP118 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR 0.125 3 TSSOP-8 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR 0.125DEG 3DE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*