參數資料
型號： LM75BDP
廠商： NXP Semiconductors N.V.
元件分類： 工業控制
英文描述： Digital temperature sensor and thermal watchdog
封裝： LM75BD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<Always Pb-free,;LM75BD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<Always Pb-free,;
文件頁數： 11/29頁
文件大小： 164K
代理商： LM75BDP
LM75B_2
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 — 9 December 2008
11 of 29
NXP Semiconductors
LM75B
Digital temperature sensor and thermal watchdog
7.7 OS fault queue
Fault queue is defined as the number of faults that must occur consecutively to activate
the OS output. It is provided to avoid false tripping due to noise. Because faults are
determined at the end of data conversions, fault queue is also defined as the number of
consecutive conversions returning a temperature trip. The value of fault queue is
selectable by programming the two bits B4 and B3 (OS_F_QUE[1:0]) in register Conf.
Notice that the programmed data and the fault queue value are not the same.
Table 13
shows the one-to-one relationship between them. At power-up, fault queue data = 0 and
fault queue value = 1.
7.8 Shutdown mode
The device operation mode is selected by programming bit B0 (SHUTDOWN) of register
Conf. Setting bit SHUTDOWN to logic 1 will put the device into shutdown mode. Resetting
bit SHUTDOWN to logic 0 will return the device to normal mode.
In shutdown mode, the device draws a small current of approximately 1.0
μ
A and the
power dissipation is minimized; the temperature conversion stops, but the I
2
C-bus
interface remains active and register write/read operation can be performed. When the
shutdown is set, the OS output will be unchanged in comparator mode and reset in
interrupt mode.
7.9 Power-up default and power-on reset
The LM75B always powers-up in its default state with:
Normal operation mode
OS comparator mode
T
th(ots)
= 80
°
C
T
hys
= 75
°
C
OS output active state is LOW
Pointer value is logic 00 (Temp)
When the power supply voltage is dropped below the device power-on reset level of
approximately 1.0 V (POR) for over 2
μ
s and then rises up again, the device will be reset
to its default condition as listed above.
Table 13.
Fault queue data
OS_F_QUE[1]
0
0
1
1
Fault queue table
Fault queue value
Decimal
1
2
4
6
OS_F_QUE[0]
0
1
0
1
相關PDF資料
PDF描述
LM75BGD Digital temperature sensor and thermal watchdog
LM75BD Digital temperature sensor and thermal watchdog
LM75BDP Digital temperature sensor and thermal watchdog
LM75BGD Digital temperature sensor and thermal watchdog
LM78L12A 3-Terminal 0.1A Positive Voltage Regulator
相關代理商/技術參數
參數描述
LM75BDP,118 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 20C TS DIGITAL TEMP SENSOR RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM75BDP,118-CUT TAPE 制造商:NXP 功能描述:LM75 Series Digital Temperature Sensor/Thermal Watchdog Surface Mount- TSSOP - 8
LM75BDP/DG,118 功能描述:板上安裝溫度傳感器 DIGITAL TEMP SENSOR AND THERMAL WATCHDOG RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
LM75BDP118 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS
LM75BGD 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8-UXSON 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8-UXSON 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8-UXSON; IC Output Type:Digital; Sensing Accuracy Range: 3C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:SON; No. of ;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*