- 您現在的位置：買賣IC網 > PDF目錄377649 > LM75BDP (NXP Semiconductors N.V.) Digital temperature sensor and thermal watchdog PDF資料下載
參數資料
| 型號： | LM75BDP |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | Digital temperature sensor and thermal watchdog |
| 封裝： | LM75BD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<Always Pb-free,;LM75BD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<Always Pb-free,; |
| 文件頁數： | 5/29頁 |
| 文件大小： | 164K |
| 代理商： | LM75BDP |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
LM75B_2
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 02 — 9 December 2008
5 of 29
NXP Semiconductors
LM75B
Digital temperature sensor and thermal watchdog
In OS comparator mode, the OS output behaves like a thermostat. It becomes active
when the Temp exceeds the T
th(ots)
, and is reset when the Temp drops below the T
hys
.
Reading the device registers or putting the device into shutdown does not change the
state of the OS output. The OS output in this case can be used to control cooling fans or
thermal switches.
In OS interrupt mode, the OS output is used for thermal interruption. When the device is
powered-up, the OS output is first activated only when the Temp exceeds the T
th(ots)
; then
it remains active indefinitely until being reset by a read of any register. Once the OS output
has been activated by crossing T
th(ots)
and then reset, it can be activated again only when
the Temp drops below the T
hys
; then again, it remains active indefinitely until being reset
by a read of any register. The OS interrupt operation would be continued in this sequence:
T
th(ots)
trip, Reset, T
hys
trip, Reset, T
th(ots)
trip, Reset, T
hys
trip, Reset, etc. Putting the
device into the shutdown mode by setting the bit 0 of the configuration register also resets
the OS output.
In both cases, comparator mode and interrupt mode, the OS output is activated only if a
number of consecutive faults, defined by the device fault queue, has been met. The fault
queue is programmable and stored in the two bits, B3 and B4, of the Configuration
register. Also, the OS output active state is selectable as HIGH or LOW by setting
accordingly the configuration register bit B2.
At power-up, the device is put into normal operation mode, the T
th(ots)
is set to 80
°
C, the
T
hys
is set to 75
°
C, the OS active state is selected LOW and the fault queue is equal to 1.
The temp reading data is not available until the first conversion is completed in about
100 ms.
The OS response to the temperature is illustrated in
Figure 5
.
(1) OS is reset by either reading register or putting the device in shutdown mode. It is assumed that
the fault queue is met at each T
th(ots)
and T
hys
crossing point.
Fig 5.
OS response to temperature
002aae334
(1)
(1)
(1)
T
th(ots)
T
hys
OS reset
OS active
OS reset
OS active
OS output in comparator mode
OS output in interrupt mode
reading temperature limits
相關PDF資料 |
PDF描述 |
|---|---|
| LM75BGD | Digital temperature sensor and thermal watchdog |
| LM78L12A | 3-Terminal 0.1A Positive Voltage Regulator |
| LM78L05A | 3-Terminal 0.1A Positive Voltage Regulator |
| LMA1009 | 12 x 12-Bit Multiplier-Accumulator(12 x 12位乘法器-累加器) |
| LMA2009JC20 | 12 x 12-bit Multiplier-Accumulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM75BDP,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 20C TS DIGITAL TEMP SENSOR RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BDP,118-CUT TAPE | 制造商:NXP 功能描述:LM75 Series Digital Temperature Sensor/Thermal Watchdog Surface Mount- TSSOP - 8 |
| LM75BDP/DG,118 | 功能描述:板上安裝溫度傳感器 DIGITAL TEMP SENSOR AND THERMAL WATCHDOG RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75BDP118 | 制造商:NXP Semiconductors 功能描述:DIGITAL TEMP SENSOR IC 11BIT +/-3C TS |
| LM75BGD | 制造商:NXP Semiconductors 功能描述:IC TEMP SENSOR DIGITAL 8-UXSON 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8-UXSON 制造商:NXP Semiconductors 功能描述:IC, TEMP SENSOR, DIGITAL, 8-UXSON; IC Output Type:Digital; Sensing Accuracy Range: 3C; Sensing Temperature Min:-55C; Sensing Temperature Max:+125C; Supply Voltage Min:2.8V; Supply Voltage Max:5.5V; Sensor Case Style:SON; No. of ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。