- 您現在的位置：買賣IC網 > PDF目錄358876 > LM80CIMT-3 (NATIONAL SEMICONDUCTOR CORP) Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | LM80CIMT-3 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| 中文描述： | 7-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO24 |
| 封裝： | PLASTIC, TSSOP-24 |
| 文件頁數： | 8/29頁 |
| 文件大小： | 435K |
| 代理商： | LM80CIMT-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Test Circuit
Functional Description
1.0 GENERAL DESCRIPTION
The LM80 provides 7 analog inputs, a temperature sensor, a
Delta-Sigma ADC (Analog-to-Digital Converter), 2 fan speed
counters, WATCHDOG registers, and a variety of inputs and
outputs on a single chip. A two wire Serial Bus interface is
provided. The LM80 performs power supply, temperature,
fan control and fan monitoring for personal computers.
The LM80 continuously converts analog inputs to 8-bit digital
words with a 10 mV LSB (Least Significant Bit) weighting,
yielding input ranges of 0 to 2.56V. The Analog inputs are in-
tended to be connected to the several power supplies
present in a a typical computer. Temperature can be con-
verted to a 9-bit or 12-bit two’s complement word with reso-
lutions of 0.5C LSB or 0.0625C LSB, respectively.
Fan inputs can be programmed to accept either fan failure
indicator or tachometer signals. Fan failure signals can be
programmed to be either active high or active low. Fan inputs
measure the period of tachometer pulses from the the fans,
providing a higher count for lower fan speeds. The fan inputs
are digital inputs with and acceptable range of 0 to V
volts
and a transition level of approximately V
+
/2 volts. Full scale
fan counts are 255 (8-bit counter), which represent a
stopped or very slow fan. Nominal speed based on a count
of 153, are programmable from 1100 to 8800 RPM. Signal
conditioning circuitry is included to accommodate slow rise
and fall times.
The LM80 provides a number of internal registers, as de-
tailed in Figure 4 These include:
Configuration Register:
Provides control and configura-
tion.
Interrupt Status Registers:
tus of each WATCHDOG limit or Interrupt event.
Interrupt Mask Registers:
Interrupt sources, as well as separate masking for each of
both hardware Interrupt outputs.
Two registers to provide sta-
Allows masking of individual
Fan Divisor/RST_OUT/OS Registers:
ister contain the divisor bits for FAN1 and FAN2 inputs. Bits
6-7 control the function of the RST_OUT/OS output.
OS Configuration/Temperature Resolution Register:
The
configuration of the OS (Overtemperature Shutdown) is con-
trolled by the lower 3 bits of this register. Bit 3 enables 12-bit
temperature conversions. Bits 4-7 reflect the lower four bits
of the temperature reading for a 12-bit resolution.
Value RAM:
The monitoring results: temperature, voltages,
fan counts, and Fan Divisor/RST_OUT/OS Register limits
are all contained in the Value RAM. The Value RAM consists
of a total of 32 bytes. The first 10 bytes are all of the results,
the next 20 bytes are the Fan Divisor/RST_OUT/OS Regis-
ter limits, and are located at 20h-3Fh, including two unused
bytes in the upper locations.
When the LM80 is started, it cycles through each measure-
ment in sequence, and it continuously loops through the se-
quence approximately once every second. Each measured
value is compared to values stored in WATCHDOG, or Limit
registers. When the measured value violates the pro-
grammed limit the LM80 will set a corresponding Interrupt in
the Interrupt Status Registers. Two hardware Interrupt lines,
INT and RST_OUT/OS are available. INT is fully program-
mable with masking of each Interrupt source, and masking of
each output. RST_OUT/OS is dedicated to the temperature
reading WATCHDOG registers. In addition, the Fan Divisor
register has control bits to enable or disable the hardware In-
terrupts.
Additional digital inputs are provided for chaining of INT, out-
puts of multiple external LM75 temperature sensors via the
BTI (Board Temperature Interrupt) input, and a CI (Chassis
Intrusion) input. The Chassis Intrusion input is designed to
accept an active high signal from an external circuit that
latches when the case is removed from the computer.
Bits 0-5 of this reg-
DS100040-6
FIGURE 3. Digital Output Load Test Circuitry
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM80CIMT-31 | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM832 | LM832 Dynamic Noise Reduction System DNR |
| LM832M | LM832 Dynamic Noise Reduction System DNR |
| LM832N | LM832 Dynamic Noise Reduction System DNR |
| LM833D | DUAL OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM80CIMT-3/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM80CIMT-31 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| LM80CIMT3NOPB | 制造商:Texas Instruments 功能描述:Processor Supervisor 24-Pin TSSOP Rail |
| LM80CIMT5 | 制造商:Texas Instruments 功能描述: |
| LM80CIMT-5 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。