- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9011M (NATIONAL SEMICONDUCTOR CORP) Multipole Connector; Gender:Male; Number of Contacts:9; Series:1625P; Body Material:PA Polyamide (Nylon) 6/6; Connecting Termination:Crimp; Number of Rows:3; Operating Voltage:250V; Pitch Spacing:1.57mm PDF資料下載
參數資料
| 型號： | LM9011M |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 其它接口 |
| 英文描述： | Multipole Connector; Gender:Male; Number of Contacts:9; Series:1625P; Body Material:PA Polyamide (Nylon) 6/6; Connecting Termination:Crimp; Number of Rows:3; Operating Voltage:250V; Pitch Spacing:1.57mm |
| 中文描述： | SPECIALTY INTERFACE CIRCUIT, PDSO28 |
| 封裝： | PLASTIC, SOIC-28 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 332K |
| 代理商： | LM9011M |
Circuit Description
(Continued)
Ground cannot be detected. The internal logic is unable to
discern which output pin is above the Fault Threshold Volt-
age, only that a pin is. Thus, the logical requirement of an Sx
pin voltage above the Fault Threshold voltage is met and no
fault is reported.
The output rise and fall times are basically a function of the
output current drive (source and sink) and the output load
characteristics. Due to the scaling of the output stages, and
variations in the value of S_HI, the fall time will typically be
two to ten times longer than the rise time for a given capaci-
tive load.
Since the output fault detection mode changes immediately
with the status of the ENB pin, and the voltage on the output
pin cannot change instantly, the FAULT pin will go low during
the output transition times. The FAULT pin will stay low until
the output voltage rises above, or falls below, the active fault
threshold. See Figure 15.
When switching the outputs from the active mode to the TRI-
STATE mode the ENB should be taken low first. This will
take all of the outputs low. Then the RESET pin can be taken
low. This will eliminate false ’open’ faults that will be gener-
ated while waiting for the one output that was high, to dis-
charge any capacitance below the V
FAULT
threshold.
DS101264-25
Figure 15. FAULT Pin Output During Normal Operation
L
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM9022 | Vacuum Fluorescent Display Filament Driver |
| LM9022M | Vacuum Fluorescent Display Filament Driver |
| LM9022N | Vacuum Fluorescent Display Filament Driver |
| LM903 | Fluid Level Detector |
| LM903N | Fluid Level Detector |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9011M/NOPB | 功能描述:IC INTERFACE ELECT IGNITN 28SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LM9011MX | 功能描述:IC INTERFACE ELECT IGNITN 28SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LM9013G/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Amplifier Transistors |
| LM9013H | 制造商:ON Semiconductor 功能描述: |
| LM9013LY | 制造商:SILVERFOX 功能描述:LABEL YELL 90X13MM 40/SHEET PK10 制造商:SILVERFOX 功能描述:LABEL, YELL, 90X13MM, 40/SHEET, PK10 制造商:SILVERFOX 功能描述:LABEL, YELL, 90X13MM, 40/SHEET, PK10; Cable Diameter Min:10mm; Marker Dimensions:13mm x 90mm; Legend:Blank; Marker Colour:Yellow; Marker Material:Polyester; SVHC:No SVHC (19-Dec-2012); Accessory Type:Labels; Body Material:Polyester; ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。