- 您現在的位置：買賣IC網 > PDF目錄361035 > LM903 (National Semiconductor Corporation) Fluid Level Detector PDF資料下載
參數資料
| 型號： | LM903 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Fluid Level Detector |
| 中文描述： | 液位檢測器 |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 148K |
| 代理商： | LM903 |
Application Hints
INTERNAL COMBUSTION ENGINE OIL LEVEL
The basic system provides a single shot measurement
when the supply is applied and has a primary application in
automotive oil, hydraulic fluid and coolant monitoring. Partic-
ularly in the case of the oil level, a valid measurement is
only possible before the oil is disturbed. The application cir-
cuit shown is arranged such that the measurement is made
when the ignition is switched on via switch A. Switch B is the
oil pressure sensor and is closed before the engine starts,
keeping pin 7 low and enabling the measurement.
STALLING AND RESTART PROTECTION
The 4M7 resistor and 10
m
F capacitor connected to pin 7
provide the restart protection. When oil pressure builds up,
switch B opens and the 10
m
F capacitor charges through
the bulb. At switch-off, the capacitor discharges slowly and
is capable of preventing a low state on pin 7 for 1 minute.
Unless pin 7 is low, a new measurement can not be made
and the previous measurement result stored in the memory
capacitor on pin 15 is used to control the output.
MEMORY
The pin 15 memory output goes high if a correct measure-
ment is made (lamp off). If the power is removed, pin 15
leakage is less than 3
m
A and the memory status is retained
for some time. Provided pin 15 voltage does not fall below
3V, the memory capacitor will be refreshed on powering up
again. There is no internal pull down on detecting an incor-
rect measurement. If it is required to use pin 15 as an output
indicating the measurement result, an external pull down
resistor and buffer will be required.
CONTINUOUS WARNING LAMP
The lamp can be arranged to light continuously by disabling
the oscillator with a resistor of 150k or less, connected be-
tween pins 10 and 11.
REPETITIVE MEASUREMENTS
Measurements may be repeated by strobing the supply to
pin 6. The probe current regulator transistor must have the
same supply as pin 6, but the warning lamp can be perma-
nently powered. The lamp will light during each measure-
ment and will flash in between measurements when incor-
rect conditions are detected.
ALTERNATIVE APPLICATIONS
Gas flow detection:
The cooling effect of gas flowing over
a probe could be used to provide a warning signal from the
LM903 in the event of gas failure.
Automatic top up:
With the LM903 strobed continuously,
the output may be stored, buffered, and used to drive sole-
noid valves to correct a fluid level as required.
6
相關PDF資料 |
PDF描述 |
|---|---|
| LM903N | Fluid Level Detector |
| LM9040 | Dual Lambda Sensor Interface Amplifier |
| LM9040M | Dual Lambda Sensor Interface Amplifier |
| LM9044 | LM9044 Lambda Sensor Interface Amplifier |
| LM9044V | LM9044 Lambda Sensor Interface Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9035A | 制造商:PEPPERL+FUCHS 功能描述:Remote I/O - LB, 241101 |
| LM9036 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra-Low Quiescent Current Voltage Regulator |
| LM9036_08 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra-Low Quiescent Current Voltage Regulator |
| LM9036DT-3.3 | 功能描述:IC REG LDO 3.3V 50MA TO-252 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.1V 輸入電壓:最高 5.5V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:300mA 電流 - 限制（最?。?420mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商設備封裝:TSOT-23-5 包裝:帶卷 (TR) |
| LM9036DT-3.3/NOPB | 制造商:Texas Instruments 功能描述:LDO Regulator Pos 3.3V 0.05A 3-Pin(2+Tab) TO-252 Rail 制造商:Texas Instruments 功能描述:IC REG LDO 3.3V 0.05A TO252-3 |
發布緊急采購，3分鐘左右您將得到回復。