參數資料
型號： LM92CIMX/NOPB
廠商： National Semiconductor
文件頁數： 8/25頁
文件大小： 1472K
描述： IC SENSOR TEMP/THERM COMP 8-SOIC
標準包裝： 2,500
系列： PowerWise®
功能： 溫度監控系統（傳感器）
傳感器類型： 內部
感應溫度： -55°C ~ 150°C
精確度： ±1.5°C（最小值）
拓?fù)洌?/td> ADC，比較器，寄存器庫
輸出類型： 2 線串行，I²C?
輸出警報： 是
輸出風扇： 無
電源電壓： 2.7 V ~ 5.5 V
工作溫度： -55°C ~ 150°C
安裝類型： 表面貼裝
封裝/外殼： 8-SOIC（0.154"，3.90mm 寬）
供應商設備封裝： 8-SOP
包裝： 帶卷 (TR)
其它名稱： *LM92CIMX
*LM92CIMX/NOPB
LM92CIMX
LM92CIMX-ND
LM92CIMX/NOPBTR
LM 92
SNIS110D MARCH 2000REVISED MARCH 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The LM92 temperature sensor incorporates a band-gap type temperature sensor, 13-bit ADC, and a digital
comparator with user-programmable upper and lower limit values. The comparator activates either the INT line
for temperatures outside the T
LOW
and T
HIGH
window, or the T_CRIT_A line for temperatures which exceed
T_CRIT. The lines are programmable for mode and polarity.
TEMPERATURE COMPARISON
LM92 provides a window comparison against a lower (T
LOW
) and upper (T
HIGH
) trip point. A second upper trip
point (T_CRIT) functions as a critical alarm shutdown. Figure 7 depicts the comparison function as well as the
modes of operation.
Status Bits
The internal Status bits operate as follows:
True:   Temperature  above  a  T
HIGH
or  T_CRIT  is  true  for  those  respective  bits.  A  true  for  T
LOW
is
temperature below T
LOW
.
False:   Assuming temperature has previously crossed above T
HIGH
or T_CRIT, then the temperature must
drop below the points corresponding T
HYST
(T
HIGH
 T
HYST
or T_CRIT  T
HYST
) in order for the condition to be
false. For T
LOW
, assuming temperature has previously crossed below T
LOW
, a false occurs when temperature
goes above T
LOW
+ T
HYST
.
The Status bits are not affected by reads or any other actions, and always represent the state of temperature vs.
setpoints.
Hardwire Outputs
The T_CRIT_A hardwire output mirrors the T_CRIT_A flag, when the flag is true, the T_CRIT_A output is
asserted at all times regardless of mode. Reading the LM92 has no effect on the T_CRIT_A output, although the
internal conversion is restarted.
The behavior of the INT hardwire output is as follows:
Comparator Interrupt Mode (Default):  User reading part resets output until next measurement completes. If
condition is still true, output is set again at end of next conversion cycle. For example, if a user never reads the
part, and temperature goes below T
LOW
then INT becomes active. It would stay that way until temperature goes
above T
LOW
+ T
HYST
. However if the user reads the part, the output would be reset. At the end of the next
conversion cycle, if the condition is true, it is set again. If not, it remains reset.
Event Interrupt Mode:   User reading part resets output until next condition "event" occurs (in other words,
output is only set once for a true condition, if reset by a read, it remains reset until the next triggering threshold
has been crossed). Conversely, if a user never read the part, the output would stay set indefinitely after the first
event that set the output. An event for Event Interrupt Mode is defined as:
1.  Transitioning upward across a setpoint, or
2.  Transitioning downward across a setpoint's corresponding hysteresis (after having exceeded that setpoint).
For example, if a user never read the part, and temperature went below T
LOW
then INT would become active. It
would stay that way forever if a user never read the part.
However if the user read the part, the output would be reset. Even if the condition is true, it will remain reset. The
temperature must cross above T
LOW
+ T
HYST
to set the output again.
In either mode, reading any register in the LM92 restarts the conversion. This allows a designer to know exactly
when the LM92 begins a comparison. This prevents unnecessary Interrupts just after reprogramming setpoints.
Typically, system Interrupt inputs are masked prior to reprogramming trip points. By doing a read just after
resetting trip points, but prior to unmasking, unexpected Interrupts are prevented.
Avoid programming setpoints so close that their hysteresis values overlap. An example would be that with a
T
HYST
value of 2 癈 then setting T
HIGH
and T
LOW
to within 4 癈 of each other will violate this restriction. To be
more specific, with T
HYST
set to 2 癈 assume T
HIGH
set to 64 癈. If T
LOW
is set equal to, or higher than 60 癈 this
restriction is violated.
8
Submit Documentation Feedback
Copyright ?20002013, Texas Instruments Incorporated
Product Folder Links: LM92
相關PDF資料
PDF描述
LT1123CST#TRPBF IC REG CTRLR SGL 5V SOT223
LT1248IS#PBF IC PFC CTRLR AVERAGE CURR 16SOIC
LT1249IS8#PBF IC PFC CTRLR AVERAGE CURR 8SOIC
LT1577CS-3.3/2.8#TRPBF IC REG CTRLR DUAL OUT 16SOIC
LT1640HIN8#PBF IC CONTRLR HOTSWAP NEGVOLT 8-DIP
相關代理商/技術參數
參數描述
LM93 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Hardware Monitor with Integrated Fan Control for Server Management
LM93-1001 制造商:FLOWLINE 功能描述:Two Indicator, Windowed, 1/8 DIN, PC (13.9"h x 8.5"w x 6.7"d)
LM936-SWH 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel
LM936-SWHBM 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel
LM936-SWHC4 功能描述:基本/快動開關 Foot Switch RoHS:否 制造商:Omron Electronics 觸點形式:SPDT 執行器:Lever 電流額定值:5 A 電壓額定值 AC:250 V 電壓額定值 DC:30 V 功率額定值: 工作力:120 g IP 等級:IP 67 NEMA 額定值: 端接類型:Wire 安裝:Panel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*