- 您現在的位置：買賣IC網 > PDF目錄361035 > LM9831CCVJDX (NATIONAL SEMICONDUCTOR CORP) LM9831 42-Bit Color, 1200dpi USB Image Scanner PDF資料下載
參數資料
| 型號： | LM9831CCVJDX |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | LM9831 42-Bit Color, 1200dpi USB Image Scanner |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 36/41頁 |
| 文件大?。?/td> | 320K |
| 代理商： | LM9831CCVJDX |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁當前第36頁第37頁第38頁第39頁第40頁第41頁
36
www.national.com
14.1.5 Pixel Rate Shading Multiplier
The shading multiplier uses all 16 bits of data.
There is an important difference between the pixel rate shading
multiplier of the LM9830 and the LM9831. In the LM9830, if the
value for the shading multiplier was 0, the gain through the multi-
plier was 1V/V. The LM9830 also had 3 multiplier gain ranges: 1
to 1.5, 1 to 2.0, and 1 to 3.0 V/V.
The LM9831 has a simpler multiplier with only one gain range: 0
to 4 V/V. The gain of the multiplier is
Gain = (gain code)/16384 V/V
Note that if the gain code = 0, then the pixel is multiplied by 0! In
other words, if the gain coefficient is set to 0, the output of the
multiplier will be all 0s. A gain code of 0 was not unusual for the
LM9830, but will not work with the LM9831. To maintain a mini-
mum gain of 1V/V, make sure the gain code is 16384 or higher.
If desired, gains between 0 and 1 V/V can be used, but they will
usually result in less dynamic range and noisier images.
14.1.6 The Gamma Table
The LM9831’s 3 gamma tables are 12 bits wide, instead of 10 bits
(LM9830). This means each gamma curve has 4 times the num-
ber of datapoints and you can now get 4 times the accuracy avail-
able with the LM9830.
Since most consumer CCDs have a true SNR of less than 12 bits,
the LM9831 does not support a 14 bit gamma table, freeing up an
additional 36kwords of DRAM memory.
14.1.7 General DataPort Information
There have been several important changes to the dataport.
The read-only Pause bit is now in register 3. You can write this bit
in order to write to the other bits in the register, but anything you
write to the Pause bit will be ignored.
There are now 2 bits to select between Offset Coefficients, Gain
Coefficients, and Gamma data.
In the LM9830, Offset and Gain coefficients were combined to
make one 16 bit word, written to register 6 as 2 bytes.
In the LM9831, Offset is a 16 bit word, and Gain is a 16 bit word.
Offset and Gain data each have a separate dataport address.
Register 5 will auto increment after 2 bytes are written to register
6 in Offset mode or Gain mode (reg03b1 = 0).
Gamma data is 8 bits wide, as in the LM9830. Register 5 will auto
increment after 1 gamma byte is written to register 6 in Gamma
mode (reg03b1 = 1).
The bit locations for selecting color (R, G, or B), have been
shifted left by 1 bit.
The DataPort address width is now 14 bits wide. This caused the
R/W bit to be shifted left by 1 bit.
When using 1 Channel Grayscale, the LM9830 ignored the color
bits in register 3. This has been fixed in the LM9831. Register 3
controls the gamma table color.
Make sure your software takes all of these changes into account.
14.2 Porting Step 2
Once your TWAIN driver is operating with the LM9831, you can
start taking advantage of the LM9831’s additional features.
14.2.1 1200 DPI
The LM9831 can support line widths up to 16384 pixels x 3 col-
ors. This allows 1200dpi scanners with a maximum width of 13.6”
(B-size).
14.2.2 Integration Time Adjustment Function
Due to DRAM speed limitations, the maximum speed at which the
LM9831 can store pixels is 1MHz. The ADC can run at speeds up
to 6MHz, but only when the HDPI divider is set to divide-by-6 or
greater, which results in a pixel rate of 1MHz or less.
This can be a challenge when scanning at high resolutions. For
example, a 600dpi 8.5” wide color CCD scanner digitizes 15,300
pixels/line. At a 1MHz rate, the resulting integration time
is15.3ms. Integration times above 10ms may be problematic in
some designs.
To allow shorter integration times without violating the 1MHz max
pixel rate, the LM9831 has an Integration Time Adjust (ITA) func-
tion (Figure 47). ITA generates 2 alternating timebases for the
CCD timing, a high frequency timebase, and a lower frequency
timebase. During the high frequency timebase, the integration
time (t
INT1
) is short, as short as the total number of pixels in a line
divided by 6MHz. (Using the previous example, that would be
2.5ms). During t
INT1
, data is clocked out of the CCD but it is not
digitized by the AFE. The CCD output signal (representing line “n-
1”) is discarded.
After the short integration time, the clock is slowed for the next
integration time (t
INT2
). Integration for line “n+1” is done during
this period. Since t
INT2
is longer, there is more time to read out
pixel data for line “n”. As long as t
corresponds to a pixel rate
of 1MHz or slower, the line can be digitized and written to the
DRAM.
t
INT 1
is determined by the traditional calculations, primarily the
MCLK divider and line end settings. t
INT2
= ITA * t
INT1
.
There are two more considerations when using the ITA. The first
is CCD image lag. Image lag is a sensor phenomenon in which a
percentage of the pixel voltage from the previous line appears in
the pixel voltage for the current line. In the example above, some
of the signal from line n-1 will leak into line n. Since the integra-
discard
Figure 47:
Integration Time Adjust Function
TR
t
INT1
t
INT2
line n
line n+1
line n-1
t
INT2
= ITA * t
INT1
Pixel
Data
line n
line n-2
相關PDF資料 |
PDF描述 |
|---|---|
| LM9832CCVJD | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832 | LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9833CCVJD | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM9833 | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM98501CCVBH | 10-Bit, 27 MSPS Camera Signal Processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9832 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LM9832 42-Bit Color, 1200dpi USB Image Scanner |
| LM9832B-B WAF | 制造商:Texas Instruments 功能描述: |
| LM9832B-E WAF | 制造商:Texas Instruments 功能描述: |
| LM9832CCVJD | 功能描述:IC SCANNER CLR USB IMAGE 100TQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模擬前端 (AFE) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:- 通道數:2 功率（瓦特）:- 電壓 - 電源，模擬:3 V ~ 3.6 V 電壓 - 電源，數字:3 V ~ 3.6 V 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:帶卷 (TR) |
| LM9832CCVS-B | 制造商:Texas Instruments 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。