- 您現在的位置：買賣IC網 > PDF目錄358878 > LM99CIMMX (National Semiconductor Corporation) 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface PDF資料下載
參數資料
| 型號： | LM99CIMMX |
| 廠商： | National Semiconductor Corporation |
| 元件分類： | 溫度/濕度傳感器 |
| 英文描述： | 【1C Accurate, High Temperature, Remote Diode Temperature Sensor with Two-Wire Interface |
| 中文描述： | 【集成電路準確，高溫，遠程二極管溫度傳感器，兩線接口 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 349K |
| 代理商： | LM99CIMMX |
1.0 Functional Description
(Continued)
1.2.2 ALERT Output as an Interrupt
The LM99’s ALERT output can be implemented as a simple
interrupt signal when it is used to trigger an interrupt service
routine. In such systems it is undesirable for the interrupt flag
to repeatedly trigger during or before the interrupt service
routine has been completed. Under this method of operation,
during a read of the STATUS REGISTER the LM99 will set
the ALERT mask bit (D7 of the Configuration register) if any
bit in the STATUS REGISTER is set, with the exception of
Busy (D7) and OPEN (D2). This prevents further ALERT
triggering until the master has reset the ALERT mask bit, at
the end of the interrupt service routine. The STATUS REG-
ISTER bits are cleared only upon a read command from the
master (see
Figure 4
) and will be re-asserted at the end of
the next conversion if the triggering condition(s) persist(s). In
order for the ALERT to be used as a dedicated interrupt
signal, bit D0 (the ALERT configure bit) in the FILTER and
ALERT CONFIGURE REGISTER (xBF) must be set low.
This is the power–on default state.
The following sequence describes the response of a system
that uses the ALERT output pin as a interrupt flag:
1.
Master Senses ALERT low
2.
Master reads the LM99 STATUS REGISTER to deter-
mine what caused the ALERT
3.
LM99 clears STATUS REGISTER, resets the ALERT
HIGH and sets the ALERT mask bit (D7 in the Configu-
ration register).
4.
Master attends to conditions that caused the ALERT to
be triggered. The fan is started, setpoint limits are ad-
justed, etc.
5.
Master resets the ALERT mask (D7 in the Configuration
register).
1.2.3 ALERT Output as an SMBus ALERT
When the ALERT output is connected to one or more ALERT
outputs of other SMBus compatible devices and to a master,
an SMBus alert line is created. Under this implementation,
the LM99’s ALERT should be operated using the ARA (Alert
Response Address) protocol. The SMBus 2.0 ARA protocol,
defined in the SMBus specification 2.0, is a procedure de-
signed to assist the master in resolving which part generated
an interrupt and service that interrupt while impeding system
operation as little as possible.
The SMBus alert line is connected to the open-drain ports of
all devices on the bus thereby AND’ing them together. The
ARA is a method by which with one command the SMBus
master may identify which part is pulling the SMBus alert line
LOW and prevent it from pulling it LOW again for the same
triggering condition. When an ARA command is received by
all devices on the bus, the devices pulling the SMBus alert
line LOW, first, send their address to the master and second,
release the SMBus alert line after recognizing a successful
transmission of their address.
The SMBus 1.1 and 2.0 specification state that in response
to an ARA (Alert Response Address) “after acknowledging
the slave address the device must disengage its SMBALERT
pulldown”. Furthermore, “if the host still sees SMBALERT
low when the message transfer is complete, it knows to read
the ARA again”. This SMBus “disengaging of SMBALERT”
requirement prevents locking up the SMBus alert line. Com-
petitive parts may address this “disengaging of SMBALERT”
requirement differently than the LM99 or not at all. SMBus
systems that implement the ARA protocol as suggested for
the LM99 will be fully compatible with all competitive parts.
The LM99 fulfills “disengaging of SMBALERT” by setting the
ALERT mask bit (bit D7 in the Configuration register, at
address 09h) after successfully sending out its address in
response to an ARA and releasing the ALERT output pin.
Once theALERT mask bit is activated, the ALERT output pin
will be disabled until enabled by software. In order to enable
the ALERT the master must read the STATUS REGISTER,
at address 02h, during the interrupt service routine and then
reset theALERT mask bit in the Configuration register to 0 at
the end of the interrupt service routine.
The following sequence describes the ARA response proto-
col.
20053831
FIGURE 3. ALERT Comparator Temperature Response
Diagram
20053828
FIGURE 4. ALERT Output as an Interrupt Temperature
Response Diagram
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LM9V381 | Color STN-LCD Module |
| LMC-S1D16 | 16 Characters X 1Lines LCD Mode |
| LMC6001AIH | JT 11C 11#16 PIN PLUG |
| LMC6001CIN | Ultra Ultra-Low Input Current Amplifier |
| LMC6001BIN | Ultra Ultra-Low Input Current Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM99CIMMX/NOPB | 功能描述:板上安裝溫度傳感器 RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM99EVAL | 功能描述:BOARD EVALUATION LM99 RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:PowerWise® 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| LM99EVAL/NOPB | 功能描述:溫度傳感器開發工具 LM99 EVAL BOARD RoHS:否 制造商:Texas Instruments 產品類型:Temperature Sensors and Control ICs 工具用于評估:MSP430G2553 接口類型:USB 工作電源電壓: 工作電源電流: |
| LM9V381 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Color STN-LCD Module |
| LMA100.A.BI.001 | 功能描述:829MHz, 1.9GHz, 2.6GHz Panel RF Antenna 698MHz ~ 960MHz, 1.71GHz ~ 2.17GHz, 2.5GHz ~ 2.7GHz 5.1dBi Connector, SMA Male Base Mount 制造商:taoglas limited 系列:- 包裝:散裝 零件狀態:有效 頻率組:寬帶 頻率（中心/帶）:829MHz，1.9GHz，2.6GHz 頻率范圍:698MHz ~ 960MHz，1.71GHz ~ 2.17GHz，2.5GHz ~ 2.7GHz 天線類型:面板 頻帶數:3 VSWR:- 回波損耗:- 增益:5.1dBi 功率 - 最大值:- 特性:- 端接:連接器，SMA 公型 侵入防護:IP67 安裝類型:基座 高度（最大值）:1.437"（36.50mm） 應用:- 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。