參數資料
型號： LMC1983CIN
廠商： NATIONAL SEMICONDUCTOR CORP
元件分類： 音頻控制
英文描述： Pushbutton Switch; Actuator Style:Rectangular; Circuitry:DPST-1NO/1NC; Switch Operation:On-(On); Contact Current Max:5A; Collar Shape:Rectangular; Features:Illuminated; Leaded Process Compatible:Yes; Mounting Type:PCB
中文描述： 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDIP28
封裝： 0.600 INCH, PLASTIC, DIP-28
文件頁數： 6/14頁
文件大?。?/td> 331K
代理商： LMC1983CIN
Pin Description
CLK (1)
The INTERMETAL (IM) Bus clock is
applied to the CLOCK pin. This input
accepts a TTL or CMOS level signal.
The input is used to clock the DATA
signal. A data bit must be valid on the
rising clock edge.
Internally tied high to V
+
through a
30 k
pull-up resistor, these inputs al-
low a peripheral device to place any
single-bit, active low digital information
onto the IM Bus. It is then sent out to
the controlling device through the
DATA pin. Examples of such informa-
tion could include indication of the
presence of a Second Audio Program
(SAP) or an FM stereo carrier.
These are the LMC1983’s three stereo
input pairs.
The selected INPUT signal is available
at this output. This feature allows ex-
ternal signal processors such as noise
reduction or graphic equalizers to be
used. This output can typically sink
1 mA. These pins should be capaci-
tively coupled to pins 8 and 21, re-
spectively, if no external processor is
used.
These are the inputs that an external
signal processor uses to return a sig-
nal to the LMC1983. These pins
should be capacitively coupled to pins
7 and 22, respectively, if no external
processor is used.
These are the inputs to the tone con-
trol amplifier. See the Application Infor-
mation section titled “Tone Control Re-
sponse”.
Tone control amplifier output. See the
Application Information section titled
“Tone Control Response”.
These outputs are used with external
tone control capacitors. Internally, this
output is applied to the volume attenu-
ators.
The output signal on these pins is a
voltage taken from the volume attenu-
ator’s 40 dB tap point. An external
R–C network is connected to these
pins.
The output signal from these pins
drives a stereo power amplifier. The
output can typically sink 1 mA.
A 10 μF capacitor is connected be-
DIGITAL INPUT
1 & 2 (2, 3)
INPUTS 1, 2 & 3
(4, 25; 5, 24; 6, 23)
SELECT OUT
(7, 22)
SELECT IN
(8, 21)
TONE IN
(9, 20)
TONE OUT
(10, 19)
OP AMP
OUT (11, 18)
LOUDNESS
(12, 17)
MAIN
OUTPUT
(13, 16)
BYPASS (14)
tween this pin and ground to provide
an
AC
ground
half-supply voltage reference.
This
pin
is
connected
ground.
This is the power supply connection.
The LMC1983 is operational with sup-
ply voltages from 6V to 12V. This pin
should be bypassed to ground through
a 1.0 μF capacitor.
This is the IDENTITY digital input that,
when low, signals the LMC1983 to re-
ceive, from a controlling device, a de-
vice address (40
H
–47
H
), present on
the DATA line.
This is the serial data input for commu-
nications sent by a controller. The con-
troller must have open drain outputs
used with external pull-up resistors.
The data rate has a maximum fre-
quency of 1 MHz. The LMC1983 re-
quires 16 bits of data to control or
change a function: the first 8 bits select
the LMC1983 and one of eight func-
tions. The final eight bits set the func-
tion to a desired value. The data must
be valid on the rising edge of the
CLOCK input signal.
for
the
internal
GROUND (15)
to
analog
V
+
(26)
ID (27)
DATA (28)
General Information
The LMC1983 is a CMOS/bipolar building block intended for
high fidelity audio signal processing. It is designed for line
level inputs signals (300 mV 2V) and has a maximum gain
of 0.5 dB. While the LMC1983 is manufactured with CMOS
processing, NPN transistors are used to build low noise op
amps. The combination of CMOS switches, bipolar op amps,
and poly-silicon resistors make it possible to achieve an or-
der of magnitude quality improvement over other bipolar cir-
cuits that use analog multipliers to accomplish gain adjust-
ment. Internal circuits set the volume to minimum, tone
controls to flat, the mute to on, and all other functions off
when power is first applied. Individual left and right volume
controls are software programmed to achieve the stereo bal-
ance function. Figure 1 shows the connection diagram of a
typical LMC1983 application.
The LMC1983 has internal decoding logic that allows a mi-
croprocessor (μP) or microcontroller (μC) to communicate di-
rectly to the audio control circuitry through an INTERMETAL
(IM) Bus interface. This three-wire interface consists of a
bi-directional DATA line, a Clock (CLK) input line, and an
Identity (ID) line. Address and function selection data (8 bits)
are serially shifted from the controller to the LMC1983. This
is followed by 8 bits of function value data. Data present in
the internal shift register is latched and the instruction is
executed.
www.national.com
6
相關PDF資料
PDF描述
LMC1983CIV Digitally-Controlled Stereo Tone and Volume Circuit with Three Selectable Stereo Inputs
LMC1992 LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
LMC1992CCN LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
LMC2001 High Precision, 6MHz Rail-To-Rail Output Operational Amplifier
LMC2001ACM5 High Precision, 6MHz Rail-To-Rail Output Operational Amplifier
相關代理商/技術參數
參數描述
LMC1983CIV 制造商:Rochester Electronics LLC 功能描述:- Bulk
LMC1983CIVX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Tone/Volume/Balance Control
LMC1992 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
LMC1992CCN 制造商:NSC 制造商全稱:National Semiconductor 功能描述:LMC1992 Digitally-Controlled Stereo Tone and Volume Circuit with Four-Channel Input-Selector
LMC200 制造商:Black Box Corporation 功能描述:14 SLOT POWER CHASSIS W/1 POWE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*