- 您現在的位置：買賣IC網 > PDF目錄358878 > LMC6001 (National Semiconductor Corporation) Ultra Ultra-Low Input Current Amplifier PDF資料下載
參數資料
| 型號： | LMC6001 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Ultra Ultra-Low Input Current Amplifier |
| 中文描述： | 超超低輸入電流放大器 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 305K |
| 代理商： | LMC6001 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁
Applications Hints
(Continued)
Although the LMC6001 is highly stable over a wide range of
operating conditions, certain precautions must be met to
achieve the desired pulse response when a large feedback
resistor is used. Large feedback resistors with even small
values of input capacitance, due to transducers, photo-
diodes, and circuit board parasitics, reduce phase margins.
When high input impedances are demanded, guarding of the
LMC6001 is suggested. Guarding input lines will not only re-
duce leakage, but lowers stray input capacitance as well.
(See Printed-Circuit-Board Layout for High Impedance
Work).
The effect of input capacitance can be compensated for by
adding a capacitor, C
f
, around the feedback resistors (as in
Figure 1 ) such that:
or
R
1
C
IN
≤
R
2
C
f
Since it is often difficult to know the exact value of C
, C
can
be experimentally adjusted so that the desired pulse re-
sponse is achieved. Refer to the LMC660 and LMC662 for a
more
detailed
discussion
on
capacitance.
compensating
for
input
CAPACITIVE LOAD TOLERANCE
All rail-to-rail output swing operational amplifiers have volt-
age gain in the output stage. A compensation capacitor is
normally included in this integrator stage. The frequency lo-
cation of the dominant pole is affected by the resistive load
on the amplifier. Capacitive load driving capability can be op-
timized by using an appropriate resistive load in parallel with
the capacitive load (see Typical Curves).
Direct capacitive loading will reduce the phase margin of
many op-amps. A pole in the feedback loop is created by the
combination of the op-amp’s output impedance and the ca-
pacitive load. This pole induces phase lag at the unity-gain
crossover frequency of the amplifier resulting in either an os-
cillatory or underdamped pulse response. With a few exter-
nal components, op amps can easily indirectly drive capaci-
tive loads, as shown in Figure 2
In the circuit of Figure 2 R1 and C1 serve to counteract the
loss of phase margin by feeding the high frequency compo-
nent of the output signal back to the amplifier’s inverting in-
put, thereby preserving phase margin in the overall feedback
loop.
Capacitive load driving capability is enhanced by using a pul-
lup resistor to V
(Figure 3). Typically a pullup resistor con-
ducting 500 μA or more will significantly improve capacitive
load responses. The value of the pullup resistor must be de-
termined based on the current sinking capability of the ampli-
fier with respect to the desired output swing. Open loop gain
of the amplifier can also be affected by the pullup resistor
(see Electrical Characteristics).
PRINTED-CIRCUIT-BOARD LAYOUT
FOR HIGH-IMPEDANCE WORK
It is generally recognized that any circuit which must operate
with less than 1000 pA of leakage current requires special
layout of the PC board. When one wishes to take advantage
of the ultra-low bias current of the LMC6001, typically less
than 10 fA, it is essential to have an excellent layout. Fortu-
nately, the techniques of obtaining low leakages are quite
simple. First, the user must not ignore the surface leakage of
the PC board, even though it may sometimes appear accept-
ably low, because under conditions of high humidity or dust
or contamination, the surface leakage will be appreciable.
To minimize the effect of any surface leakage, lay out a ring
of foil completely surrounding the LMC6001’s inputs and the
terminals of capacitors, diodes, conductors, resistors, relay
terminals, etc., connected to the op-amp’s inputs, as in Fig-
DS011887-5
FIGURE 1. Cancelling the Effect of Input Capacitance
DS011887-6
FIGURE 2. LMC6001 Noninverting Gain of 10 Amplifier,
Compensated to Handle Capacitive Loads
DS011887-7
FIGURE 3. Compensating for Large Capacitive
Loads with a Pullup Resistor
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LMC6008 | 8 Channel Buffer |
| LMC6008IM | 8 Channel Buffer |
| LMC6008IMX | 8 Channel Buffer |
| LMC6034IM | LIGHT PIPE 2WIDE 3MM ROUND |
| LMC6034IN | CMOS Quad Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LMC6001AIH | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Ultra Ultra-Low Input Current Amplifier |
| LMC6001AIN | 功能描述:運算放大器 - 運放 RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LMC6001AIN/NOPB | 功能描述:運算放大器 - 運放 ULTRA ULTRA-LOW INPUT CURRENT AMP RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| LMC6001AIN/NOPB | 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC |
| LMC6001BIH | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。