- 您現在的位置：買賣IC網 > PDF目錄358902 > LOG112 Precision, High-Speed Transimpedance Amplifier PDF資料下載
參數資料
| 型號： | LOG112 |
| 元件分類： | 跨阻放大器 |
| 英文描述： | Precision, High-Speed Transimpedance Amplifier |
| 中文描述： | 精密，高速互阻抗放大器 |
| 文件頁數： | 9/18頁 |
| 文件大?。?/td> | 362K |
| 代理商： | LOG112 |
"#$
%"#$
SBOS291E NOVEMBER 2003 REVISED NOVEMBER 2004
www.ti.com
9
APPLICATIONS INFORMATION
BASIC OPERATION
The OPA380 is a high-performance transimpedance
amplifier with very low 1/f noise. As a result of its unique
architecture, the OPA380 has excellent long-term input
voltage offset stability—a 300-hour life test at 150
°
C
demonstrated
randomly
approximately equal to measurement repeatability of
1
μ
V.
The OPA380 performance results from an internal
auto-zero amplifier combined with a high-speed
amplifier. The OPA380 has been designed with circuitry
to improve overload recovery and settling time over a
traditional composite approach. It has been specifically
designed and characterized to accommodate circuit
options to allow 0V output operation (see Figure 3).
The OPA380 is used in inverting configurations, with the
noninverting input used as a fixed biasing point.
Figure 1 shows the OPA380 in a typical configuration.
Power-supply pins should be bypassed with 1
μ
F ceramic
or tantalum capacitors. Electrolytic capacitors are not
recommended.
distributed
variation
OPA380
V
OUT(1)
(0.5V to 4.4V)
V
BIAS
= 0.5V
+5V
1
μ
F
R
F
C
F
λ
NOTE: (1) V
OUT
= 0.5V in dark conditions.
Figure 1. OPA380 typical configuration
OPERATING VOLTAGE
OPA380 series op amps are fully specified from 2.7V to
5.5V over a temperature range of 40
°
C to +125
°
C.
Parameters that vary significantly with operating
voltages or temperature are shown in the Typical
Characteristics.
INTERNAL OFFSET CORRECTION
The OPA380 series op amps use an auto-zero topology
with a time-continuous 90MHz op amp in the signal
path. This amplifier is zero-corrected every 100
μ
s using
a proprietary technique. Upon power-up, the amplifier
requires approximately 400
μ
s to achieve specified V
OS
accuracy, which includes one full auto-zero cycle of
approximately 100
μ
s and the start-up time for the bias
circuitry. Prior to this time, the amplifier will function
properly but with unspecified offset voltage.
This design has virtually no aliasing and very low noise.
Zero correction occurs at a 10kHz rate, but there is very
little fundamental noise energy present at that
frequency due to internal filtering. For all practical
purposes, any glitches have energy at 20MHz or higher
and are easily filtered, if required. Most applications are
not sensitive to such high-frequency noise, and no
filtering is required.
INPUT VOLTAGE
The input common-mode voltage range of the OPA380
series extends from V to (V+) –1.8V. With input signals
above this common-mode range, the amplifier will no
longer provide a valid output value, but it will not latch
or invert.
INPUT OVERVOLTAGE PROTECTION
Device inputs are protected by ESD diodes that will
conduct if the input voltages exceed the power supplies
by more than approximately 500mV. Momentary
voltages greater than 500mV beyond the power supply
can be tolerated if the current is limited to 10mA. The
OPA380 series feature no phase inversion when the
inputs extend beyond supplies if the input is current
limited.
相關PDF資料 |
PDF描述 |
|---|---|
| LOGT670-J | Multi TOPLED |
| LOGT670-JL | Multi TOPLED |
| LOGT670-K | Multi TOPLED |
| LOGT670-HK | Multi TOPLED |
| LOGT671 | Multi TOPLED Bright Green Die |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LOG112AID | 功能描述:對數放大器 Precision Log & Log Ratio Amp RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| LOG112AID | 制造商:Texas Instruments 功能描述:IC AMP LOG SMD SOIC14 112 |
| LOG112AIDE4 | 功能描述:對數放大器 Precision Log & Log Ratio Amp RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| LOG112AIDR | 功能描述:對數放大器 Precision Log & Log Ratio Amp RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
| LOG112AIDRE4 | 功能描述:對數放大器 Precision Log & Log Ratio Amp RoHS:否 制造商:Texas Instruments 通道數量:3 帶寬:3 dB 共模抑制比（最小值）: 輸入補償電壓:+/- 7 mV 輸入電壓范圍（最大值）:5.5 V 工作電源電壓:4.5 V to 5.5 V 電源電流:+/- 15 mA 工作溫度范圍:- 40 C to +85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。