- 您現在的位置：買賣IC網 > PDF目錄358923 > LP3883ET-1.5 (NATIONAL SEMICONDUCTOR CORP) 3A Fast-Response Ultra Low Dropout Linear Regulators PDF資料下載
參數資料
| 型號： | LP3883ET-1.5 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 3A Fast-Response Ultra Low Dropout Linear Regulators |
| 中文描述： | 1.5 V FIXED POSITIVE LDO REGULATOR, 0.42 V DROPOUT, PZFM5 |
| 封裝： | TO-220, 5 PIN |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 367K |
| 代理商： | LP3883ET-1.5 |
Typical Performance
Characteristics
Unless otherwise specified: T
A
=
25C, C
= 4.7μF, Cin = 4.7μF, S/D pin is tied to V
BIAS
,
V
IN
= 2.2V, V
OUT
= 1.8V. (Continued)
V
BIAS
PSRR
20062421
Application Hints
V
BIAS
RESTRICTIONS FOR PROPER START-UP
To prevent misoperation, ensure that V
is below 50mV
before start-up is initiated. This scenario can occur in sys-
tems with a backup battery using reverse-biased "blocking"
diodes which may allow enough leakage current to flow into
the V
node to raise it’s voltage slightly above ground
when the main power is removed. Using low leakage diodes
or a resistive pull down can prevent the voltage at V
BIAS
from
rising above 50mV. Large bulk capacitors connected to
V
BIAS
may also cause a start-up problem if they do not
discharge fully before re-start is initiated (but only if V
BIAS
is
allowed to fall below 1V). A resistor connected across the
capacitor will allow it to discharge more quickly. It should be
noted that the probability of a "false start" caused by incor-
rect logic states is extremely low.
EXTERNAL CAPACITORS
To assure regulator stability, input and output capacitors are
required as shown in the Typical Application Circuit.
OUTPUT CAPACITOR
At least 4.7μF of output capacitance is required for stability
(the amount of capacitance can be increased without limit).
The output capacitor must be located less than 1 cm from
the output pin of the IC and returned to a clean analog
ground. The ESR (equivalent series resistance) of the output
capacitor must be within the "stable" range as shown in the
graph below over the full operating temperature range for
stable operation.
20062431
Minimum ESR vs Output Load Current
Tantalum capacitors are recommended for the output as
their ESR is ideally suited to the part’s requirements and the
ESR is very stable over temperature. Aluminum electrolytics
are not recommended because their ESR increases very
rapidly at temperatures below 10C. Aluminum caps can only
be used in applications where lower temperature operation
is not required.
A second problem with Al caps is that many have ESR’s
which are only specified at low frequencies. The typical loop
bandwidth of a linear regulator is a few hundred kHz to
several MHz. If an Al cap is used for the output cap, it must
be one whose ESR is specified at a frequency of 100 kHz or
more.
Because the ESR of ceramic capacitors is only a few milli
Ohms, they are not suitable for use as output capacitors on
LP388X devices. The regulator output can tolerate ceramic
capacitance totaling up to 15% of the amount of Tantalum
capacitance connected from the output to ground.
OUTPUT "BYPASS" CAPACITORS
Many designers place small value "bypass" capacitors at
various circuit points to reduce noise. Ceramic capacitors in
the value range of about 1000pF to 0.1μF placed directly on
the output of a PNP or P-FET LDO regulator can cause a
loss of phase margin which can result in oscillations, even
when a Tantalum output capacitor is in parallel with it. This is
not unique to National Semiconductor LDO regulators, it is
true of any P-type LDO regulator.
The reason for this is that PNP or P-FET regulators have a
higher output impedance (compared to an NPN regulator),
which results in a pole-zero pair being formed by every
different capacitor connected to the output.
The zero frequency is approximately:
F
z
= 1 / (2 X
π
X ESR X C)
Where ESR is the equivalent series resistance of the capaci-
tor, and C is the value of capacitance.
The pole frequency is:
F
p
= 1 / (2 X
π
X R
L
X C)
Where R
L
is the load resistance connected to the regulator
output.
To understand why a small capacitor can reduce phase
margin: assume a typical LDO with a bandwidth of 1MHz,
which is delivering 0.5A of current from a 2.5V output (which
means R
is 5 Ohms). We then place a .047 μF capacitor on
the output. This creates a pole whose frequency is:
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LP3883ET-1.2 | 3A Fast-Response Ultra Low Dropout Linear Regulators |
| LP38841T-1.2 | 0.8A Ultra Low Dropout Linear Regulators Stable with Ceramic Output Capacitors |
| LP38841S-0.8 | 0.8A Ultra Low Dropout Linear Regulators Stable with Ceramic Output Capacitors |
| LP38841T-1.5 | 0.8A Ultra Low Dropout Linear Regulators Stable with Ceramic Output Capacitors |
| LP38841SX-0.8 | INLET, IEC, 16A, NON-ILLUMINATED, CB; Connector type:IEC; Gender:Plug; Current rating:16A; Voltage rating, AC:250V; Outlets, No. of:1; Termination method:Solder Lug; Series:POLYSNAP; Mounting type:Panel; Approval Bodies:UL RoHS Compliant: Yes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP38841 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:0.8A Ultra Low Dropout Linear Regulators Stable with Ceramic Output Capacitors |
| LP38841-ADJ | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:0.8A Ultra Low Dropout Adjustable Linear Regulators Stable with Ceramic Output Capacitors |
| LP38841EVAL | 功能描述:電源管理IC開發工具 LP38841 EVAL BOARD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| LP38841MR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Texas Instruments 功能描述: |
| LP38841MR-ADJ | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
發布緊急采購，3分鐘左右您將得到回復。