- 您現在的位置：買賣IC網 > PDF目錄358928 > LP3988IMF-3.0 (NATIONAL SEMICONDUCTOR CORP) Micropower, 150mA Ultra Low-Dropout CMOS Voltage Regulator With Power Good PDF資料下載
參數資料
| 型號： | LP3988IMF-3.0 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Micropower, 150mA Ultra Low-Dropout CMOS Voltage Regulator With Power Good |
| 中文描述： | 3 V FIXED POSITIVE LDO REGULATOR, 0.15 V DROPOUT, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 292K |
| 代理商： | LP3988IMF-3.0 |
Application Hints
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP3988 requires external
capacitors for regulator stability. The LP3988 is specifically
designed for portable applications requiring minimum board
space and smallest components. These capacitors must be
correctly selected for good performance.
INPUT CAPACITOR
An input capacitance of
)
1μF is required between the
LP3988 input pin and ground (the amount of the capacitance
may be increased without limit).
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analog
ground.Any good quality ceramic, tantalum, or film capacitor
may be used at the input.
Important:
Tantalum capacitors can suffer catastrophic fail-
ures due to surge current when connected to a low-
impedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR on the input capaci-
tor, but tolerance and temperature coefficient must be con-
sidered when selecting the capacitor to ensure the capaci-
tance will be
)
1μF over the entire operating temperature
range.
OUTPUT CAPACITOR
The LP3988 is designed specifically to work with very small
ceramic output capacitors. A ceramic capacitor (dielectric
types Z5U, Y5V or X7R) in 1 to 22 μF range with 5m
to
500m
ESR range is suitable in the LP3988 application
circuit.
It may also be possible to use tantalum or film capacitors at
the output, but these are not as attractive for reasons of size
and cost (see next section Capacitor Characteristics).
The output capacitor must meet the requirement for mini-
mum amount of capacitance and also have an ESR (Equiva-
lent Series Resistance) value which is within a stable range
(5 m
to 500 m
).
NO-LOAD STABILITY
The LP3988 will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3988 is designed to work with ceramic capacitors on
the output to take advantage of the benefits they offer: for
capacitance values in the range of 1μF to 4.7μF range,
ceramic capacitors are the smallest, least expensive and
have the lowest ESR values (which makes them best for
eliminating high frequency noise). The ESR of a typical 1μF
ceramic capacitor is in the range of 20 m
to 40 m
, which
easily meets the ESR requirement for stability by the
LP3988.
The ceramic capacitor’s capacitance can vary with tempera-
ture. Most large value ceramic capacitors (
)
2.2μF) are
manufactured with Z5U or Y5V temperature characteristics,
which results in the capacitance dropping by more than 50%
as the temperature goes from 25C to 85C.
A better choice for temperature coefficient in a ceramic
capacitor is X7R, which holds the capacitance within
±
15%.
Tantalum capacitors are less desirable than ceramic for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
1μF to 4.7μF range.
Another important consideration is that tantalum capacitors
have higher ESR values than equivalent size ceramics. This
means that while it may be possible to find a tantalum
capacitor with an ESR value within the stable range, it would
have to be larger in capacitance (which means bigger and
more costly ) than a ceramic capacitor with the same ESR
value. It should also be noted that the ESR of a typical
tantalum will increase about 2:1 as the temperature goes
from 25C down to 40C, so some guard band must be
allowed.
ON/OFF INPUT OPERATION
The LP3988 is turned off by pulling the V
EN
pin low, and
turned on by pulling it high. If this feature is not used, the V
EN
pin should be tied to V
IN
to keep the regulator output on at all
time. To assure proper operation, the signal source used to
drive the V
EN
input must be able to swing above and below
the specified turn-on/off voltage thresholds listed in the Elec-
trical Characteristics section under V
IL
and V
IH
.
FAST ON-TIME
The LP3988 utilizes a speed up circuitry to ramp up the
internal V
voltage to its final value to achieve a fast
output turn on time.
L
www.national.com
9
相關PDF資料 |
PDF描述 |
|---|---|
| LP3988IMF-2.85 | Micropower, 150mA Ultra Low-Dropout CMOS Voltage Regulator With Power Good |
| LP3988 | Micropower, 150mA Ultra Low-Dropout CMOS Voltage Regulator With Power Good |
| LP3990SD-1.8 | 150mA Linear Voltage Regulator for Digital Applications |
| LP3990SD-2.5 | 150mA Linear Voltage Regulator for Digital Applications |
| LP3990SD-2.8 | 150mA Linear Voltage Regulator for Digital Applications |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP3988IMF30NOPB | 制造商:Texas Instruments 功能描述: |
| LP3988IMFX-2.5 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3988IMFX-2.5/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP3988IMFX-2.6 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Micropower, 150mA Ultra Low-Dropout CMOS Voltage Regulator With Power Good |
| LP3988IMFX-2.85 | 制造商:Texas Instruments 功能描述:LDO Regulator Pos 2.85V 0.15A 5-Pin SOT-23 T/R |
發布緊急采購，3分鐘左右您將得到回復。