- 您現在的位置：買賣IC網 > PDF目錄358930 > LP5900 (National Semiconductor Corporation) Ultra Low Noise, 100 mA Linear Regulator for RF/Analog Circuits Requires No Bypass Capacitor PDF資料下載
參數資料
| 型號： | LP5900 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Ultra Low Noise, 100 mA Linear Regulator for RF/Analog Circuits Requires No Bypass Capacitor |
| 中文描述： | 超低噪音，100 mA線性射頻/模擬電路需要調節無旁路電容 |
| 文件頁數： | 8/10頁 |
| 文件大小： | 645K |
| 代理商： | LP5900 |
Typical Performance Characteristics.
Unless otherwise specified,C
IN
= C
OUT
= 0.47μF, V
IN
=
V
OUT(NOM)
+ 1.0V, V
EN
= 1.2V, I
OUT
= 1mA , T
A
= 25
o
C. (Continued)
Enable Start-up Time, (I
L
= 1mA, V
OUT
= 2.8V)
Enable Start-up Time, (I
L
= 100mA, V
OUT
= 2.8V)
20144146
20144147
Dropout Over Temperature (100mA)
20144105
Application Hints
POWER DISSIPATION AND DEVICE OPERATION
The permissible power dissipation for any package is a
measure of the capability of the device to pass heat from the
power source, the junctions of the IC, to the ultimate heat
sink, the ambient environment. Thus the power dissipation is
dependent on the ambient temperature and the thermal
resistance across the various interfaces between the die and
ambient air. As stated in (Note 5) of the electrical character-
istics, the allowable power dissipation for the device in a
given package can be calculated using the equation:
The actual power dissipation across the device can be rep-
resented by the following equation:
P
D
= (V
IN
– V
OUT
) x I
OUT
This establishes the relationship between the power dissipa-
tion allowed due to thermal consideration, the voltage drop
across the device, and the continuous current capability of
the device. These two equations should be used to deter-
mine the optimum operating conditions for the device in the
application.
EXTERNAL CAPACITORS
Like any low-dropout regulator, the LP5900 requires external
capacitors for regulator stability. The LP5900 is specifically
designed for portable applications requiring minimum board
space and smallest components. These capacitors must be
correctly selected for good performance.
INPUT CAPACITOR
An input capacitor is required for stability. The input capacitor
should be at least equal to or greater than the output capaci-
tor. It is recommended that a 0.47 μF capacitor be connected
between the LP5900 input pin and ground.
L
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| LP5900TL-2.5 | 128 x 64 pixel format, LED Backlight available |
| LP5900TL-2.8 | 128 x 64 pixel format, LED Backlight available |
| LP5900TL-3.0 | 128 x 64 pixel format, LED Backlight available |
| LP5900TL-3.3 | 128 x 64 pixel format, LED Backlight available |
| LP6-EWN1-03-N3 | SMD LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LP5900SD-1.5 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP5900SD-1.5/NOPB | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP5900SD-1.8 | 功能描述:低壓差穩壓器 - LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP5900SD-1.8/NOPB | 功能描述:低壓差穩壓器 - LDO LOW-NOISE 100MA LDO RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| LP5900SD-1.8/NOPB | 制造商:Texas Instruments 功能描述:IC, LDO VOLT REG, 3.3V, 150mA, LLP-6 |
發布緊急采購，3分鐘左右您將得到回復。