- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47M172-NR (STANDARD MICROSYSTEMS CORP) ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC PDF資料下載
參數資料
| 型號： | LPC47M172-NR |
| 廠商： | STANDARD MICROSYSTEMS CORP |
| 元件分類： | 外設及接口 |
| 英文描述： | ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
| 中文描述： | MULTIFUNCTION PERIPHERAL, PQFP128 |
| 封裝： | 14 X 20 MM, 2.7 MM HEIGHT, MQFP-128 |
| 文件頁數： | 107/228頁 |
| 文件大小： | 1269K |
| 代理商： | LPC47M172-NR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁當前第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁
KIRQ
If “EN FLAGS” has been executed and P24 is set to a one: the OBF flag is gated onto KIRQ. The KIRQ signal can be
connected to system interrupt to signify that the LPC47M192 CPU has written to the output data register via “OUT
DBB,A”. If P24 is set to a zero, KIRQ is forced low. On power-up, after a valid RST pulse has been delivered to the
device, KIRQ is reset to 0. KIRQ will normally reflects the status of writes “DBB”. (KIRQ is normally selected as IRQ1
for keyboard support.)
If “EN FLAGS” has not been executed: KIRQ can be controlled by writing to P24. Writing a zero to P24 forces KIRQ
low; a high forces KIRQ high.
SMSC DS – LPC47M192
Page 107
Rev. 03/30/05
DATASHEET
MIRQ
If “EN FLAGS” has been executed and P25 is set to a one:; IBF is inverted and gated onto MIRQ. The MIRQ signal
can be connected to system interrupt to signify that the LPC47M192 CPU has read the DBB register. If “EN FLAGS”
has not been executed, MIRQ is controlled by P25, Writing a zero to P25 forces MIRQ low, a high forces MIRQ high.
(MIRQ is normally selected as IRQ12 for mouse support).
Gate A20
A general purpose P21 is used as a software controlled Gate A20 or user defined output.
8042 PINS
The 8042 functions P17, P16 and P12 are implemented as in a true 8042 part. Reference the 8042 spec for all
timing. A port signal of 0 drives the output to 0. A port signal of 1 causes the port enable signal to drive the output to
1 within 20-30nsec. After 500nsec (six 8042 clocks) the port enable goes away and the external pull-up maintains
the output signal as 1.
In 8042 mode, the pins can be programmed as open drain. When programmed in open drain mode, the port enables
do not come into play. If the port signal is 0 the output will be 0. If the port signal is 1, the output tristates: an external
pull-up can pull the pin high, and the pin can be shared. In 8042 mode, the pins cannot be programmed as input nor
inverted through the GP configuration registers.
7.11.2 EXTERNAL KEYBOARD AND MOUSE INTERFACE
Industry-standard PC-AT-compatible keyboards employ a two-wire, bidirectional TTL interface for data transmission.
Several sources also supply PS/2 mouse products that employ the same type of interface. To facilitate system
expansion, the LPC47M192 provides four signal pins that may be used to implement this interface directly for an
external keyboard and mouse.
The LPC47M192 has four high-drive, open-drain output, bidirectional port pins that can be used for external serial
interfaces, such as external keyboard and PS/2-type mouse interfaces. They are KCLK, KDAT, MCLK, and MDAT.
P26 is inverted and output as KCLK. The KCLK pin is connected to TEST0. P27 is inverted and output as KDAT.
The KDAT pin is connected to P10. P23 is inverted and output as MCLK. The MCLK pin is connected to TEST1.
P22 is inverted and output as MDAT. The MDAT pin is connected to P11.
Note
: External pull-ups may be required.
7.11.3 KEYBOARD POWER MANAGEMENT
The keyboard provides support for two power-saving modes: soft powerdown mode and hard powerdown mode. In
soft powerdown mode, the clock to the ALU is stopped but the timer/counter and interrupts are still active. In hard
power down mode the clock to the 8042 is stopped.
Soft Power Down Mode
This mode is entered by executing a HALT instruction. The execution of program code is halted until either RESET is
driven active or a data byte is written to the DBBIN register by a master CPU. If this mode is exited using the
interrupt, and the IBF interrupt is enabled, then program execution resumes with a CALL to the interrupt routine,
otherwise the next instruction is executed. If it is exited using RESET then a normal reset sequence is initiated and
program execution starts from program memory location 0.
Hard Power Down Mode
This mode is entered by executing a STOP instruction. The oscillator is stopped by disabling the oscillator driver
cell. When either RESET is driven active or a data byte is written to the DBBIN register by a master CPU, this mode
will be exited (as above). However, as the oscillator cell will require an initialization time, either RESET must be held
active for sufficient time to allow the oscillator to stabilize. Program execution will resume as above.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47N267-MN | 100 Pin LPC Notebook I/O with X-Bus Interface |
| LPC47N227-MN | 100 Pin Super I/O with LPC Interface for Notebook Applications |
| LPC47N227TQFP | 100 Pin Super I/O with LPC Interface for Notebook Applications |
| LPC47M182-NR | ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
| LPC47M182-NW | ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47M172-NW | 功能描述:輸入/輸出控制器接口集成電路 Enhanced Super I/O Contrllr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47M182 | 制造商:SMSC 制造商全稱:SMSC 功能描述:ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
| LPC47M182_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:Advanced I/O Controller with Motherboard GLUE Logic |
| LPC47M182E-NW | 功能描述:輸入/輸出控制器接口集成電路 Advanced I/O Ctrl MotherBoard GLUE RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47M182-NR | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。