- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47N217-JN (SMSC Corporation) 64 - PIN SUPUR I/O WITH LPC INTERFACE PDF資料下載
參數資料
| 型號： | LPC47N217-JN |
| 廠商： | SMSC Corporation |
| 英文描述： | 64 - PIN SUPUR I/O WITH LPC INTERFACE |
| 中文描述： | 64 -針蘇布爾的I / LPC接口? |
| 文件頁數： | 118/228頁 |
| 文件大?。?/td> | 1269K |
| 代理商： | LPC47N217-JN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁當前第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁
Note 2
: GP36-GP37 and GP40 should not be connected to any VTR powered external circuitry. These
pins are not used for wakeup.
Note 3
: GP60 and GP61 have LED functionality which must be active under VTR so its buffer is
powered by VTR.
Note 4
: These pins can be used for wakeup events to generate a PME while the part is under VTR power
(VCC=0).
Note 5
: These pins cannot be used for wakeup events to generate a PME while the part is under VTR power
(VCC=0). The GP32, GP33 and GP53 pins come up as output and low on a VCC POR and PCI reset.
Note 6
: GP43 defaults to the GPIO function on VCC POR and PCI Reset.
7.12.6 EITHER EDGE TRIGGERED INTERRUPTS
Six GPIO pins are implemented such that they allow an interrupt (PME or SMI) to be generated on both a high-to-low
and a low-to-high edge transition, instead of one or the other as selected by the polarity bit.
The either edge triggered interrupts (EETI) function as follows: If the EETI function is selected for the GPIO pin, then
the bits that control input/output, polarity and open drain/push-pull have no effect on the function of the pin. However,
the polarity bit does affect the value of the GP bit (i.e., register GP2, bit 2 for GP22).
A PME or SMI interrupt occurs if the PME or SMI enable bit is set for the corresponding GPIO and the EETI function
is selected on the GPIO. The PME or SMI status bits are set when the EETI pin transitions (on either edge) and are
cleared on a write of ‘1’. There are also status bits for the EETIs located in the MSC_STS register, which are also
cleared on a write of ‘1’. The MSC_STS register provides the status of all of the EETI interrupts within one register.
The PME, SMI or MSC status is valid whether or not the interrupt is enabled and whether or not the EETI function is
selected for the pin.
Miscellaneous Status Register (MSC_STS) is for the either edge triggered interrupt status bits. If the EETI function is
selected for a GPIO then both a high-to-low and a low-to-high edge will set the corresponding MSC status bits.
Status bits are cleared on a write of ‘1’. See the “Runtime Registers” section for more information.
The configuration register for the either edge triggered interrupt status bits is defined in the “Runtime Registers”
section.
7.12.7 LED FUNCTIONALITY
The LPC47M192 provides LED functionality on two GPIOs, GP60 and GP61. These pins can be configured to turn
the LED on and off and blink independent of each other through the LED1 and LED2 runtime registers at offset 0x5D
and 0x5E from the base address located in the primary base I/O address in Logical Device A.
The LED pins (GP60 and GP61) are able to control the LED while the part is under VTR power with VCC removed.
In order to control a LED while the part is under VTR power, the GPIO pin must be configured for the LED function
and either open drain or push-pull buffer type. In the case of open-drain buffer type, the pin is capable of sinking
current to control the LED. In the case of push-pull buffer type, the part will source current. The part is also able to
blink the LED under VTR power. The LED will not blink under VTR power (VCC removed) if the external 32kHz clock
is not connected.
The LED pins can drive a LED when the buffer type is configured to be push-pull and the part is powered by either
VCC or VTR, since the buffers for these pins are powered by VTR. This means they will source their specified current
from VTR even when VCC is present.
The LED control registers are defined in the “Runtime Register” section.
7.13 SYSTEM MANAGEMENT INTERRUPT (SMI)
SMSC DS – LPC47M192
Page 118
Rev. 03/30/05
DATASHEET
The LPC47M192 implements a “group” nIO_SMI output pin. The System Management Interrupt is a non-maskable
interrupt with the highest priority level used for OS transparent power management. The nSMI group interrupt output
consists of the enabled interrupts from each of the functional blocks in the chip and many of the GPIOs and the Fan
tachometer pins. The GP27/nIO_SMI pin, when selected for the nIO_SMI function, can be programmed to be active
high or active low via the polarity bit in the GP27 register. The output buffer type of the pin can be programmed to be
open-drain or push-pull via bit 7 of the GP27 register. The nIO_SMI pin function defaults to active low, open-drain
output.
The interrupts are enabled onto the group nSMI output via the SMI Enable Registers 1 to 5. The nSMI output is then
enabled onto the group nIO_SMI output pin via bit[7] in the SMI Enable Register 2. The SMI output can also be
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47N217-JV | 64 - PIN SUPUR I/O WITH LPC INTERFACE |
| LPC47N227 | 100 Pin Super I/O with LPC Interface for Notebook Applications |
| LPC47M172 | ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
| LPC47N252 | Advanced Notebook I/O Controller with On-Board FLASH |
| LPC47N267 | 100 Pin LPC Notebook I/O with X-Bus Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47N217-JV | 功能描述:輸入/輸出控制器接口集成電路 64-Pin Mobile I/O RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47N217N | 制造商:SMSC 制造商全稱:SMSC 功能描述:64-Pin Super I/O with LPC Interface |
| LPC47N217N-ABZJ | 功能描述:輸入/輸出控制器接口集成電路 3.3volts 5V tolerant RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47N217N-ABZJ-TR | 功能描述:接口 - 專用 56 Pin Super I/O LPC Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| LPC47N217N-JV | 制造商:SMSC 制造商全稱:SMSC 功能描述:64-Pin Super I/O with LPC Interface |
發布緊急采購，3分鐘左右您將得到回復。