- 您現在的位置：買賣IC網 > PDF目錄358934 > LPC47N227 (SMSC Corporation) 100 Pin Super I/O with LPC Interface for Notebook Applications PDF資料下載
參數資料
| 型號： | LPC47N227 |
| 廠商： | SMSC Corporation |
| 英文描述： | 100 Pin Super I/O with LPC Interface for Notebook Applications |
| 中文描述： | 100針超級I / LPC接口與澳的筆記本應用 |
| 文件頁數： | 54/228頁 |
| 文件大小： | 1269K |
| 代理商： | LPC47N227 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁
7.4.4 DATA TRANSFER COMMANDS
All of the Read Data, Write Data and Verify type commands use the same parameter bytes and return the same
results information, the only difference being the coding of bits 0-4 in the first byte.
An implied seek will be executed if the feature was enabled by the Configure command. This seek is completely
transparent to the user. The Drive Busy bit for the drive will go active in the Main Status Register during the seek
portion of the command. If the seek portion fails, it is reflected in the results status normally returned for a
Read/Write Data command. Status Register 0 (ST0) would contain the error code and C would contain the cylinder
on which the seek failed.
SMSC DS – LPC47M192
Page 54
Rev. 03/30/05
DATASHEET
Read Data
A set of nine (9) bytes is required to place the FDC in the Read Data Mode. After the Read Data command has been
issued, the FDC loads the head (if it is in the unloaded state), waits the specified head settling time (defined in the
Specify command), and begins reading ID Address Marks and ID fields. When the sector address read off the
diskette matches with the sector address specified in the command, the FDC reads the sector’s data field and
transfers the data to the FIFO.
After completion of the read operation from the current sector, the sector address is incremented by one and the data
from the next logical sector is read and output via the FIFO. This continuous read function is called “Multi-Sector
Read Operation”. Upon receipt of the TC cycle, or an implied TC (FIFO overrun/underrun), the FDC stops sending
data but will continue to read data from the current sector, check the CRC bytes, and at the end of the sector,
terminate the Read Data Command.
N determines the number of bytes per sector (see Table 18 below). If N is set to zero, the sector size is set to 128.
The DTL value determines the number of bytes to be transferred. If DTL is less than 128, the FDC transfers the
specified number of bytes to the host. For reads, it continues to read the entire 128-byte sector and checks for CRC
errors. For writes, it completes the 128-byte sector by filling in zeros. If N is not set to 00 Hex, DTL should be set to
FF Hex and has no impact on the number of bytes transferred.
Table 18 – Sector Sizes
N
00
01
02
03
..
07
SECTOR SIZE
128 bytes
256 bytes
512 bytes
1024 bytes
…
16 Kbytes
The amount of data which can be handled with a single command to the FDC depends upon MT (multi-track) and N
(number of bytes/sector).
The Multi-Track function (MT) allows the FDC to read data from both sides of the diskette. For a particular cylinder,
data will be transferred starting at Sector 1, Side 0 and completing the last sector of the same track at Side 1.
If the host terminates a read or write operation in the FDC, the ID information in the result phase is dependent upon
the state of the MT bit and EOT byte. Refer to Table 19.
At the completion of the Read Data command, the head is not unloaded until after the Head Unload Time Interval
(specified in the Specify command) has elapsed. If the host issues another command before the head unloads,
then the head settling time may be saved between subsequent reads.
If the FDC detects a pulse on the nINDEX pin twice without finding the specified sector (meaning that the diskette’s
index hole passes through index detect logic in the drive twice), the FDC sets the IC code in Status Register 0 to
“01” indicating abnormal termination, sets the ND bit in Status Register 1 to “1” indicating a sector not found, and
terminates the Read Data Command.
After reading the ID and Data Fields in each sector, the FDC checks the CRC bytes. If a CRC error occurs in the ID
or data field, the FDC sets the IC code in Status Register 0 to “01” indicating abnormal termination, sets the DE bit
flag in Status Register 1 to “1”, sets the DD bit in Status Register 2 to “1” if CRC is incorrect in the ID field, and
terminates the Read Data Command. Table 20 describes the effect of the SK bit on the Read Data command
相關PDF資料 |
PDF描述 |
|---|---|
| LPC47M172 | ADVANCED I/O CONTROLLER WITH MOTHERBOARD GLUE LOGIC |
| LPC47N252 | Advanced Notebook I/O Controller with On-Board FLASH |
| LPC47N267 | 100 Pin LPC Notebook I/O with X-Bus Interface |
| LPC47M112 | ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE |
| LPC47M112-MC | ENHANCED SUPER I/O CONTROLLER WITH LPC INTERFACE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LPC47N227_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:100 Pin Super I/O with LPC Interface for Notebook Applications |
| LPC47N227MN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Peripheral IC |
| LPC47N227-MN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LPC47N227-MT | 功能描述:輸入/輸出控制器接口集成電路 Notebk I/O Contrllr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| LPC47N227-MV | 功能描述:輸入/輸出控制器接口集成電路 100-Pin Mobile I/O RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。