- 您現在的位置：買賣IC網 > PDF目錄377664 > LS7538 (LSI Corporation) TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) PDF資料下載
參數資料
| 型號： | LS7538 |
| 廠商： | LSI Corporation |
| 英文描述： | TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) |
| 中文描述： | 觸摸式控制步進調光器自動增益控制（AGC燈開關） |
| 文件頁數： | 4/4頁 |
| 文件大小： | 26K |
| 代理商： | LS7538 |
AC
MAINS
LOAD
C4
R1
R3
R4
C1
D1
FIGURE 4. TOUCH LAMP APPLICATION SCHEMATIC
C3
D2
8
7
V
SS
6
MODE CONT
5
4
3
2
1
TRIG
CLOCK SYNC V
DD
TOUCH
D3
R2
TOUCH
PLATE
(LAMP BODY)
C2
(SEE NOTE 1)
T1
G
MT2
MT1
Z1
C5
C6
R5
+
-
+V
-V
LS7538
+
-
C7*
(SEE NOTE 2)
R1 = 20k
, 1W
R2 =
470k
, 1/4W
R3 =
1k
, 1/4W
R4 =
300k
, 1/4W, 1%
R5 =
10M
, 1/4W
C1 =
47μF, 16V
C2 =
1000pF, 16V
C3 =
1000pF, 1kV
R1 =
R2 =
R4 =
D1 =
T1 =
or Q4004F41 (Typical Triac)
39k
, 2W
910k
, 1/4W
360k
, 1/4W, 1%
1N4005
Q4004L4 (Typical Triac)
All other values remain the same.
C4 = 1000pF, 1kV
C5 =
.03μF, 16V
C6 =
1μF, 16V
Z1 =
8.2V, 1/4W Zener
D1 =
1N4004
D2 =
1N4148
D3 =
1N4148
T1 =
Q2004L4 (Typical Triac)
or Q2004F41 (Typical Triac)
(1)
Resistor should be placed adjacent to Pin 1.
220VAC APPLICATION
115VAC APPLICATION
(1)
(1
NOTE 1
: Connect MODE (Pin 6) for desired Brightness Step Sequence (See Table 1).
NOTE 2
: A good PCB layout using through-hole components will provide protection for ESD introduced at the Touch Plate in the range
of 25kV. Using surface mount components and/or a poor PCB layout can reduce the ESD protection. The OEM can increase the ESD
protection provided by the product with any combination of the following steps:
Step 1
: The most effective and least costly way to increase ESD protection is to create a spark gap around the Touch Plate input on
the PCB. This will increase ESD protection on a good PCB layout to abut 35kV. The gap should be made with a split metal ring with
each side of the metal ring connected back to opposite sides of the AC line. This ensures that a path for the spark back to house ground
through AC Neutral exists independent of line plug polarity. The split ring and the center conduction plate should be constructed so that
the spacing between them conforms to UL requirements. The spark gap will absorb most of the ESD leaving a remnant of about 10kV
for the rest of the circuit to absorb.
Step 2
: Increase R3 from 1k
to 5.1k
and add C7, a 0.1μF capacitor, between V
DD
and Vss.
(A minimal loss in touch sensitivity may be experienced.)
Step 3:
Replace diodes D2 and D3 (1N4148) with Schottky diodes (1N5819 or similar)
7538/39-091100-4
相關PDF資料 |
PDF描述 |
|---|---|
| LS7539 | TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) |
| LS7540 | TOUCH CONTROL CONTINUOUS DIMMER with AUTOMATIC GAIN CONTROL (AGC) |
| LS7541 | TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) |
| LS7560N | BRUSHLESS DC MOTOR CONTROLLER |
| LS7561N | BRUSHLESS DC MOTOR CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LS7539 | 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) |
| LS7540 | 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL CONTINUOUS DIMMER with AUTOMATIC GAIN CONTROL (AGC) |
| LS7541 | 制造商:LSI 制造商全稱:LSI 功能描述:TOUCH CONTROL STEP DIMMER LIGHT SWITCH WITH AUTOMATIC GAIN CONTROL (AGC) |
| LS7548 | 制造商:TDK-Lambda Corporation 功能描述:AC/DC Power Supply Single-OUT 48V 1.6A 5-Pin 制造商:TDK-Lambda Corporation 功能描述:- Bulk |
| LS75-48 | 功能描述:線性和開關式電源 76W 48V 1.6A AC-DC 115-230VAC RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
發布緊急采購，3分鐘左右您將得到回復。