參數資料
型號: LT1013ACH
廠商: LINEAR TECHNOLOGY CORP
元件分類: 運動控制電子
英文描述: Quad Precision Op Amp
中文描述: DUAL OP-AMP, 240 uV OFFSET-MAX, MBCY8
封裝: 0.200 INCH, METAL CAN, TO-5, 8 PIN
文件頁數: 20/25頁
文件大?。?/td> 420K
代理商: LT1013ACH
LT1013, LT1013A, LT1013D, LT1013Y
DUAL PRECISION OPERATIONAL AMPLIFIERS
SLOS018B – MAY 1988 – REVISED OCTOBER 1996
20
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
comparator applications
The single-supply operation of the LT1013 lends itself for use as a precision comparator with TTL-compatible
output. In systems using both operational amplifiers and comparators, the LT1013 can perform multiple duties.
Refer to Figures 25 and 26.
VO
100 mV
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
Overdrive
10 mV
5 mV
2 mV
0
50 100 150 200 250 300 350 400 450
t – Time –
μ
s
5
4
3
2
1
0
D
I
Figure 25. Low-to-High-Level Output
Response for Various Input Overdrives
V
2 mV
5 mV
Overdrive
10 mV
0
50 100 150 200 250 300 350 400 450
t – Time –
μ
s
5
4
3
2
1
0
D
I
VCC+ = 5 V
VCC– = 0
TA = 25
°
C
100 mV
Figure 26. High-to-Low-Level Output
Response for Various Input Overdrives
low-supply operation
The minimum supply voltage for proper operation of the LT1013 is 3.4 V (three Ni-Cad batteries). Typical supply
current at this voltage is 290
μ
A; therefore, power dissipation is only 1 mW per amplifier.
offset voltage and noise testing
The test circuit for measuring input offset voltage and its temperature coefficient is shown in Figure 30. This
circuit with supply voltages increased to
±
20 V is also used as the burn-in configuration.
The peak-to-peak equivalent input noise voltage of the LT1013 is measured using the test circuit shown in
Figure 27. The frequency response of the noise tester indicates that the 0.1-Hz corner is defined by only one
zero. The test time to measure 0.1-Hz to 10-Hz noise should not exceed 10 seconds, as this time limit acts as
an additional zero to eliminate noise contribution from the frequency band below 0.1 Hz.
An input noise voltage test is recommended when measuring the noise of a large number of units. A 10-Hz input
noise voltage measurement correlates well with a 0.1-Hz peak-to-peak noise reading because both results are
determined by the white noise and the location of the 1/f corner frequency.
Current noise is measured by the circuit and formula shown in Figure 28. The noise of the source resistors is
subtracted.
相關PDF資料
PDF描述
LT1013ACJ8 Circular Connector; MIL SPEC:MIL-DTL-38999 Series II; Body Material:Metal; Series:JT; No. of Contacts:15; Connector Shell Size:14; Connecting Termination:Crimp; Circular Shell Style:Straight Plug; Body Style:Straight RoHS Compliant: No
LT1013MJ8 Quad Precision Op Amp
LT1013IS8 Quad Precision Op Amp
LT1013CJ8 Quad Precision Op Amp
LT1014AMFK QUAD PRECISION OPERATIONAL AMPLIFIERS
相關代理商/技術參數
參數描述
LT1013ACJ8 制造商:Linear Technology 功能描述:OP Amp Dual GP ±22V/44V 8-Pin CDIP
LT1013ACJG 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
LT1013ACL 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Voltage-Feedback Operational Amplifier
LT1013ACN8 功能描述:IC PRECISION OP-AMP DUAL 8-DIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源,單路/雙路(±):2 V ~ 44 V,±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP(5x3) 包裝:管件
LT1013ACN8#PBF 功能描述:IC PRECISION OP-AMP DUAL 8-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源,單路/雙路(±):3 V ~ 32 V,±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR