- 您現在的位置：買賣IC網 > PDF目錄377669 > LT1020MJ (LINEAR TECHNOLOGY CORP) Micropower Regulator and Comparator PDF資料下載
參數資料
| 型號： | LT1020MJ |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Micropower Regulator and Comparator |
| 中文描述： | 4 V-30 V ADJUSTABLE POSITIVE REGULATOR, CDIP14 |
| 封裝： | 0.300 INCH, CERAMIC, DIP-14 |
| 文件頁數： | 8/16頁 |
| 文件大?。?/td> | 364K |
| 代理商： | LT1020MJ |
8
LT1020
U
S
A
other precautions are necessary and the reference is
stable with nominal stray capacitances.
O
PPLICATI
IU
U
Like most other IC regulators, a minimum load is required
on the output of the LT1020 to maintain regulation. For
most standard regulators this is normally specified at
5mA. Of course, for a micropower regulator this would be
a tremendously large current. The output current must be
large enough to absorb all the leakage current of the pass
transistor at the maximum operating temperature. It also
affects the transient response; low output currents have
long recovery times from load transients. At high operat-
ing temperatures the minimum load current increases and
having too low of a load current may cause the output to
go unregulated. Devices are tested for minimum load
current at high temperature. The output voltage setting
resistors to the feedback terminal can usually be used to
provide the minimum load current.
Frequency Compensation
The LT1020 is frequency compensated by a dominant pole
on the output. An output capacitor of 10
μ
F is usually large
enough to provide good stability. Increasing the output
capacitor above 10
μ
F further improves stability. In order
to insure stability, a feedback capacitor is needed between
the output pin and the feedback pin. This is because stray
capacitance can form another pole with the large value of
feedback resistors used with the LT1020. Also, a feedback
capacitor minimizes noise pickup and improves ripple
rejection.
With the large dynamic operating range of the output
current, 10000:1, frequency response changes widely.
Low AC impedance capacitors are needed to insure stabil-
ity. While solid tantalum are best, aluminum electrolytics
can be used but larger capacitor values may be needed.
The CURRENT LIMIT pin allows one of the internal nodes
to be rolled off with a 0.05
μ
F capacitor to ground. With this
capacitor, lower values of regulator output capacitance
can be used (down to 1
μ
F) for low (<20mA) output
currents. Values of capacitance greater than 0.05
μ
F de-
grade the transient response, so are not recommended.
If the CURRENT LIMIT pin is connected to GND, the
current limit is decreased and only a 1
μ
F output capacitor
is needed.
When bypassing the reference, a 20
resistor must be
connected in series with the capacitor.
Figure 2. Minimizing Oscillation in Thermal Shutdown
Overload Protection
The main regulator in the LT1020 is current limited at
approximately 350mA. The current limit is stable with both
input voltage and temperature. A current limit pin, when
strapped to ground, decreases the output current. This
allows the output current to be set to a lower value than
250mA. The output current available with the current limit
pin strapped to ground is not well controlled so if precise
current limiting is desired it should be provided externally
as is shown in some of the application circuits.
If the device is overloaded for long periods of time, thermal
shutdown turns the output off. In thermal shutdown, there
may be some oscillations which can disturb external
circuitry. A diode connected between the reference and
feedback terminal provides hysteresis under thermal shut-
down, so that the device turns on and off with about a 5
second period and there are no higher frequency oscilla-
tions. This is shown in Figure 2. This diode is recom-
mended for most applications. Thermal shutdown tem-
perature is set at approximately 145
°
C.
Figure 1. Bypassing Reference
+
REF
+
REF
OUTPUT
OUTPUT
20
20
10
μ
F
10
μ
F
OR
1020 F01
4
4
+
10
μ
F
0.001
μ
F
*
2
11
4
V
OUT
FB
REF
LT1020
1020 F02
* DIODE ADDS FEEDBACK
相關PDF資料 |
PDF描述 |
|---|---|
| LT1021CMH-10 | Precision Reference |
| LT1021BCH-10 | Precision Reference |
| LT1021BCH-5 | Precision Reference |
| LT1021BCH-7 | Precision Reference |
| LT1021BCN8-10 | Precision Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1020MJ883C | 制造商:LT 功能描述:New |
| LT1021BCH-5 | 功能描述:IC VREF SERIES BURIED ZENER TO-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| LT1021BCN8-10 | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:否 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:2,000 系列:- 基準類型:旁路，可調節，精度 輸出電壓:1.24 V ~ 16 V 容差:±0.5% 溫度系數:- 輸入電壓:1.24 V ~ 16 V 通道數:1 電流 - 陰極:100µA 電流 - 靜態:- 電流 - 輸出:20mA 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:TO-226-3、TO-92-3（TO-226AA）成形引線 供應商設備封裝:TO-92-3 包裝:帶卷 (TR) |
| LT1021BCN8-10#PBF | 功能描述:IC VREF SERIES SHUNT ZNR 8-PDIP RoHS:是 類別:集成電路 (IC) >> PMIC - 電壓基準 系列:- 標準包裝:3,000 系列:- 基準類型:旁路，精度 輸出電壓:3V 容差:±0.5% 溫度系數:100ppm/°C 輸入電壓:- 通道數:1 電流 - 陰極:82µA 電流 - 靜態:- 電流 - 輸出:15mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-TSSOP（5 引線），SC-88A，SOT-353 供應商設備封裝:SC-70-5 包裝:帶卷 (TR) 其它名稱:296-20888-2 |
| LT1021BCN8-10#PBF | 制造商:Linear Technology 功能描述:IC VOLTAGE REFERENCE 10V DIP-8 制造商:Linear Technology 功能描述:IC, VOLTAGE REFERENCE, 10V, DIP-8 |
發布緊急采購，3分鐘左右您將得到回復。