- 您現在的位置：買賣IC網 > PDF目錄6023 > LT1028ACN8#PBF (Linear Technology)IC OP-AMP LOW NOISE SNGL 8-DIP PDF資料下載
參數資料
| 型號： | LT1028ACN8#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP-AMP LOW NOISE SNGL 8-DIP |
| 標準包裝： | 50 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 轉換速率： | 15 V/µs |
| 增益帶寬積： | 75MHz |
| 電流 - 輸入偏壓： | 25nA |
| 電壓 - 輸入偏移： | 10µV |
| 電流 - 電源： | 7.4mA |
| 電壓 - 電源，單路/雙路(±)： | ±4 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1317 (CN2011-ZH PDF) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT1028/LT1128
11
1028fb
applicaTions inForMaTion – noise
Voltage Noise vs Current Noise
The LT1028/LT1128’s less than 1nV/√Hz voltage noise is
three times better than the lowest voltage noise heretofore
available (on the LT1007/1037). A necessary condition for
such low voltage noise is operating the input transistors at
nearly 1mA of collector currents, because voltage noise is
inversely proportional to the square root of the collector
current. Current noise, however, is directly proportional
to the square root of the collector current. Consequently,
the LT1028/LT1128’s current noise is significantly higher
than on most monolithic op amps.
Therefore, to realize truly low noise performance it is
important to understand the interaction between voltage
noise (en), current noise (In) and resistor noise (rn).
Total Noise vs Source Resistance
The total input referred noise of an op amp is given by:
et = [en2 + rn2 + (InReq)2]1/2
where Req is the total equivalent source resistance at the
two inputs, and
rn = √4kTReq = 0.13√Req in nV/√Hz at 25°C
As a numerical example, consider the total noise at 1kHz
of the gain 1000 amplifier shown in Figure 1.
the largest term, as in the example above, and the LT1028/
LT1128’s voltage noise becomes negligible. As Req is
further increased, current noise becomes important. At
1kHz, when Req is in excess of 20k, the current noise
component is larger than the resistor noise. The total
noise versus matched source resistance plot illustrates
the above calculations.
The plot also shows that current noise is more dominant
at low frequencies, such as 10Hz. This is because resistor
noise is flat with frequency, while the 1/f corner of current
noise is typically at 250Hz. At 10Hz when Req > 1k, the
current noise term will exceed the resistor noise.
When the source resistance is unmatched, the total noise
versus unmatched source resistance plot should be con-
sulted. Note that total noise is lower at source resistances
below 1k because the resistor noise contribution is less.
When RS > 1k total noise is not improved, however. This
is because bias current cancellation is used to reduce
input bias current. The cancellation circuitry injects two
correlated current noise components into the two inputs.
With matched source resistors the injected current noise
creates a common-mode voltage noise and gets rejected
by the amplifier. With source resistance in one input only,
the cancellation noise is added to the amplifier’s inherent
noise.
In summary, the LT1028/LT1128 are the optimum am-
plifiers for noise performance, provided that the source
resistanceiskeptlow.Thefollowingtabledepictswhichop
amp manufactured by Linear Technology should be used
to minimize noise, as the source resistance is increased
beyond the LT1028/LT1128’s level of usefulness.
Table 1. Best Op Amp for Lowest Total Noise vs Source Resistance
SOURCE RESIS-
TANCE (Ω) (Note 1)
BEST OP AMP
AT LOW FREQ (10Hz)
WIDEBAND (1kHz)
0 to 400
LT1028/LT1128
400 to 4k
LT1007/1037
LT1028/LT1128
4k to 40k
LT1001
LT1007/LT1037
40k to 500k
LT1012
LT1001
500k to 5M
LT1012 or LT1055
LT1012
>5M
LT1055
Note 1: Source resistance is defined as matched or unmatched, e.g.,
RS = 1k means: 1k at each input, or 1k at one input and zero at the other.
Req = 100Ω + 100Ω || 100k ≈ 200Ω
rn = 0.13√200 = 1.84nV√Hz
en = 0.85nV√Hz
In = 1.0pA/√Hz
et = [0.852 + 1.842 + (1.0 × 0.2)2]1/2 = 2.04nV/√Hz
Output noise = 1000 et = 2.04V/√Hz
At very low source resistance (Req < 40Ω) voltage noise
dominates. As Req is increased resistor noise becomes
–
+
100
100k
100
LT1028
LT1128
1028 F01
Figure 1
相關PDF資料 |
PDF描述 |
|---|---|
| 9-146253-0-05 | CONN HDR BRKWAY .100 10POS VERT |
| LT2079IS#PBF | IC OPAMP MICROPOWER QUAD 14SOIC |
| LTC1100CSW#PBF | IC INSTRMNT AMP CHOP-STBL 16SOIC |
| OP467GPZ | IC OPAMP GP 28MHZ QUAD 14DIP |
| TSW-128-08-T-S-RA | CONN HEADER 28POS .100" SNGL R/A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1028CN8 | 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LT1028CN8#PBF | 功能描述:IC OP-AMP LOW NOISE SNGL 8-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:MicroAmplifier™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:5pA 電壓 - 輸入偏移:1500µV 電流 - 電源:220µA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 36 V，±2.25 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-29363-1 |
| LT1028CP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| LT1028CS8 | 功能描述:IC OP-AMP LOW NOISE SNGL 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LT1028CS8#PBF | 功能描述:IC OP-AMP LOW NOISE SNGL 8-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:MicroAmplifier™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:5pA 電壓 - 輸入偏移:1500µV 電流 - 電源:220µA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 36 V，±2.25 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-29363-1 |
發布緊急采購，3分鐘左右您將得到回復。