- 您現在的位置：買賣IC網 > PDF目錄377673 > LT1054 (Linear Technology Corporation) Switched-Capacitor Voltage Converter with Regulator(帶穩壓器的開關電容電壓轉換器) PDF資料下載
參數資料
| 型號： | LT1054 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Switched-Capacitor Voltage Converter with Regulator(帶穩壓器的開關電容電壓轉換器) |
| 中文描述： | 開關電容電壓轉換器穩壓器（帶穩壓器的開關電容電壓轉換器） |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 281K |
| 代理商： | LT1054 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
6
LT1054/LT1054L
PI
FU
CTIO
N
S
U
U
from being pulled above the ground pin (Pin 3) during
start-up. Any small, general purpose transistor such as
2N2222 or 2N2219 can be used. R
X
should be chosen to
provide enough base drive to the external transistor so that
it is saturated under nominal output voltage and maximum
output current conditions. In some cases an N-channel
enhancement mode MOSFET can be used in place of the
transistor.
R
X
≤
(
|
V
OUT
|
)
β
I
OUT
–
+
LOAD
C
IN
C
OUT
LT1054 F01
I
L
V
+
R
X
LT1054
GND
FB/SHDN
CAP
+
CAP
–
V
+
OSC
V
REF
V
OUT
I
Q
I
OUT
+
+
V
REF
(Pin 6):
Reference Output. This pin provides a 2.5V
reference point for use in LT1054-based regulator circuits.
The temperature coefficient of the reference voltage has
been adjusted so that the temperature coefficient of the
regulated output voltage is close to zero. This requires the
reference output to have a positive temperature coefficient
as can be seen in the typical performance curves. This
nonzero drift is necessary to offset a drift term inherent in
the internal reference divider and comparator network tied
to the feedback pin. The overall result of these drift terms
is a regulated output which has a slight positive tempera-
ture coefficient at output voltages below 5V and a slight
negative TC at output voltages above 5V. Reference output
current should be limited, for regulator feedback networks,
to approximately 60
μ
A. The reference pin will draw
≈
100
μ
A when shorted to ground and will not affect the
internal reference/regulator, so that this pin can also be
used as a pull-up for LT1054 circuits that require synchro-
nization.
OSC (Pin 7):
Oscillator Pin. This pin can be used to raise or
lower the oscillator frequency or to synchronize the device
to an external clock. Internally Pin 7 is connected to the
oscillator timing capacitor (C
t
≈
150pF) which is alternately
charged and discharged by current sources of
±
7
μ
A so that
the duty cycle is
≈
50%. The LT1054 oscillator is designed
to run in the frequency band where switching losses are
minimized. However the frequency can be raised, lowered,
or synchronized to an external system clock if necessary.
The frequency can be lowered by adding an external
capacitor (C1, Figure 2) from Pin 7 to ground. This will
increase the charge and discharge times which lowers the
oscillator frequency. The frequency can be increased by
adding an external capacitor (C2, Figure 2, in the range of
5pF to 20pF) from Pin 2 to Pin 7. This capacitor will couple
charge into C
T
at the switch transitions, which will shorten
the charge and discharge time, raising the oscillator fre-
quency. Synchronization can be accomplished by adding
an external resistive pull-up from Pin 7 to the reference pin
(Pin 6). A 20k pull-up is recommended. An open collector
gate or an NPN transistor can then be used to drive the
oscillator pin at the external clock frequency as shown in
Figure 2. Pulling up Pin 7 to an external voltage is
not recommended
. For circuits that require both fre-
quency synchronization and regulation, an external refer-
ence can be used as the reference point for the top of the
R1/R2 divider allowing Pin 6 to be used as a pull-up point
for Pin 7.
Figure 1
V
+
(Pin 8):
Input Supply. The LT1054 alternately charges
C
IN
to the input voltage when C
IN
is switched in parallel with
the input supply and then transfers charge to C
OUT
when
C
IN
is switched in parallel with C
OUT
. Switching occurs at
V
IN
C
OUT
C
IN
C2
C1
LT1054 F02
LT1054
GND
FB/SHDN
CAP
+
CAP
–
V
+
OSC
V
REF
V
OUT
+
+
Figure 2
相關PDF資料 |
PDF描述 |
|---|---|
| LT1054L | Switched-Capacitor Voltage Converter with Regulator(帶穩壓器的開關電容電壓轉換器) |
| LT1055 | Octal Buffers/Drivers With 3-State Outputs 20-PDIP 0 to 70 |
| LT1055S8 | Precision, High Speed, JFET Input Operational Amplifiers |
| LT1056CN8 | Precision, High Speed, JFET Input Operational Amplifiers |
| LT1055AM | Precision, High Speed, JFET Input Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1054CDW | 功能描述:電荷泵 Bipolar Regulated V RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LT1054CDW | 制造商:Texas Instruments 功能描述: |
| LT1054CDWE4 | 功能描述:電荷泵 Switched-Capacitor Voltage Converter RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LT1054CDWG4 | 功能描述:電荷泵 Swed-Capacitor Vltg Converters RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
| LT1054CDWR | 功能描述:電荷泵 Bipolar Regulated V RoHS:否 制造商:Maxim Integrated 功能:Inverting, Step Up 輸出電壓:- 1.5 V to - 5.5 V, 3 V to 11 V 輸出電流:100 mA 電源電流:1 mA 最大工作溫度:+ 70 C 封裝 / 箱體:SOIC-8 Narrow 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。