![](http://datasheet.mmic.net.cn/330000/LT1113ACN8_datasheet_16425748/LT1113ACN8_5.png)
5
LT1113
ELECTRICAL C
The
G
denotes specifications which apply over the temperature range –55
°
C
≤
T
A
≤
125
°
C. V
S
=
±
15V, V
CM
= 0V,
unless otherwise noted. (Note 12)
HARA TERISTICS
LT1113AM
TYP
2700
1500
±
12.5
±
12.0
3.3
3.4
5.30
5.25
1.0
1.8
92
91
LT1113M
TYP
2500
1000
±
12.5
±
12.0
3.3
3.4
5.30
5.25
1.0
2.0
92
91
SYMBOL PARAMETER
A
VOL
Large-Signal Voltage Gain
CONDITIONS (Note 4)
V
O
=
±
12V, R
L
= 10k
V
O
=
±
10V, R
L
= 1k
R
L
= 10k
R
L
= 1k
R
L
≥
2k
(Note 9)
f
O
= 100kHz
MIN
800
400
±
13.0
±
11.5
1.9
2.2
MAX
MIN
700
300
±
12.5
±
11.0
1.6
2.2
MAX
UNITS
V/mV
V/mV
G
G
V
OUT
Output Voltage Swing
G
G
V
V
SR
GBW
I
S
Slew Rate
Gain Bandwidth Product
Supply Current Per Amplifier
G
V/
μ
s
MHz
mA
mA
mV
nA
dB
dB
G
G
G
6.35
6.30
5.0
12
6.55
6.50
5.5
20
V
S
=
±
5V
V
OS
I
B+
CMRR
PSRR
Offset Voltage Match
Noninverting Bias Current Match
Common Mode Rejection Match (Note 11)
Power Supply Rejection Match
G
G
G
75
76
73
74
(Note 11)
G
Note 1:
Absolute Maximum Ratings are those values beyond which the
life of the device may be impaired.
Note 2:
The LT1113C is guaranteed functional over the Operating
Temperature Range of –40
°
C to 85
°
C. The LT1113M is guaranteed
functional over the Operating Temperature Range of –55
°
C to 125
°
C.
Note 3:
The LT1113C is guaranteed to meet specified performance from
0
°
C to 70
°
C. The LT1113C is designed, characterized and expected to
meet specified performance from –40
°
C to 85
°
C but is not tested or QA
sampled at these temperatures. For guaranteed I grade parts, consult the
factory. The LT1113M is guaranteed to meet specified performance from
–55
°
C to 125
°
C.
Note 4:
Typical parameters are defined as the 60% yield of parameter
distributions of individual amplifiers, i.e., out of 100 LT1113s (200 op
amps) typically 120 op amps will be better than the indicated
specification.
Note 5:
Warmed-up I
B
and I
OS
readings are extrapolated to a chip
temperature of 50
°
C from 25
°
C measurements and 50
°
C characterization
data.
Note 6:
Current noise is calculated from the formula:
i
n
= (2qI
B
)
1/2
where q = 1.6 10
–19
coulomb. The noise of source resistors up to 200M
swamps the contribution of current noise.
Note 7:
Input voltage range functionality is assured by testing offset
voltage at the input voltage range limits to a maximum of 2.3mV
(A grade) to 2.8mV (C grade).
Note 8:
This parameter is not 100% tested.
Note 9:
Slew rate is measured in A
V
= –1; input signal is
±
7.5V, output
measured at
±
2.5V.
Note 10:
The LT1113 is designed, characterized and expected to meet
these extended temperature limits, but is not tested at –40
°
C and 85
°
C.
Guaranteed I grade parts are available. Consult factory.
Note 11:
CMRR and
PSRR are defined as follows:
(1) CMRR and PSRR are measured in
μ
V/V on the individual
amplifiers.
(2) The difference is calculated between the matching sides in
μ
V/V.
(3) The result is converted to dB.
Note 12:
The LT1113 is measured in an automated tester in less than
one second after application of power. Depending on the package used,
power dissipation, heat sinking, and air flow conditions, the fully
warmed-up chip temperature can be 10
°
C to 50
°
C higher than the
ambient temperature.