- 您現在的位置：買賣IC網 > PDF目錄8534 > LT1204CN (Linear Technology)IC VIDEO MUX CFA 75MHZ 4IN 16DIP PDF資料下載
參數資料
| 型號： | LT1204CN |
| 廠商： | Linear Technology |
| 文件頁數： | 2/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC VIDEO MUX CFA 75MHZ 4IN 16DIP |
| 標準包裝： | 25 |
| 應用： | 4:1 多路復用器-放大器 |
| 電路數： | 1 |
| -3db帶寬： | 75MHz |
| 轉換速率： | 1000 V/µs |
| 電流 - 電源： | 19mA |
| 電流 - 輸出 / 通道： | 125mA |
| 電壓 - 電源，單路/雙路(±)： | 10 V ~ 30 V，±5 V ~ 15 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 16-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 16-PDIP |
| 包裝： | 管件 |
10
LT1204
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
Capacitance on the Inverting Input
Current feedback amplifiers require resistive feedback
from the output to the inverting input for stable operation.
Take care to minimize the stray capacitance between the
output and the inverting input. Capacitance on the invert-
ing input to ground will cause peaking in the frequency
response and overshoot in the transient response.
Capacitive Loads
The LT1204 can drive capacitive loads directly when the
proper value of feedback resistor is used. The graph of
Maximum Capacitive Load vs Feedback Resistor should
be used to select the appropriate value. The value shown
is for 5dB peaking when driving a 1k load at a gain of 2.
This is a worst-case condition. The amplifier is more
stable at higher gains and driving heavier loads. Alterna-
tively, a small resistor (10
to 20) can be put in series
with the output to isolate the capacitive load from the
amplifier output. This has the advantage that the ampli-
fier bandwidth is only reduced when the capacitive load
is present. The disadvantage is that the gain is a function
of load resistance.
Slew Rate
The slew rate of the current feedback amplifier on the
LT1204 is not independent of the amplifier gain the way
slew rate is in a traditional op amp. This is because both the
input and the output stage have slew rate limitations. In
high gain settings the signal amplitude between the nega-
tive input and any driven positive input is small and the
overall slew rate is that of the output stage. For gains less
than 10, the overall slew rate is limited by the input stage.
The input slew rate of the LT1204 is approximately 135V/
s
and is set by internal currents and capacitances. The
output slew rate is set by the value of the feedback
resistors and the internal capacitances. At a gain of 10 with
a 1k feedback resistor and
±15 supplies, the output slew
rate is typically 1000V/
s. Larger feedback resistors will
reduce the slew rate as will lower supply voltages, similar
to the way the bandwidth is reduced.
The graph, Maximum Undistorted Output vs Frequency,
relates the slew rate limitations to sinusoidal inputs for
various gain configurations.
Large-Signal Transient Response
1204 AI02
1204 AI03
VS = ±15V
AV = 2
RF = 1k
RG = 1k
RL = 400
VS = ±15V
AV = 10
RF = 910
RG = 100
RL = 400
Switching Characteristics and Pin 8
Switching between channels is a “make-before-break”
condition where both inputs are on momentarily. The
buffers isolate the inputs when the “make-before-break”
switching occurs. The input with the largest positive
voltage determines the output level. If both inputs are
equal, there is only a 40mV error at the input of the CFA
during the transition. The reference adjust (Pin 8) allows
the user to trade off positive input voltage range for
switching time. For example, on
±15V supplies, setting
the voltage on Pin 8 to – 6.8V reduces the switching
transient to a 50ns duration, and reduces the positive input
range from 6V to 2.35V. The negative input range remains
unchanged at – 6V. When switching video “in picture,” this
short transient is imperceptible even on high quality
相關PDF資料 |
PDF描述 |
|---|---|
| 1877846-1 | PLUG 6POS 0 DEG BLK/BLK 5.3-6.5 |
| LT1187CS8 | IC AMP VIDEO DIFFRNC ADJ 8-SOIC |
| VI-B3F-MU-F4 | CONVERTER MOD DC/DC 72V 200W |
| 4-1437719-8 | CONN PLUG PIN 4POS SLD PNL R/A |
| MAX5302CUA+T | IC DAC 12BIT LP SERIAL 8-UMAX |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1204CN#PBF | 功能描述:IC VIDEO MUX CFA 75MHZ 4IN 16DIP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| LT1204CS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Channel Analog Multiplexer |
| LT1204CSW | 功能描述:IC VIDEOMUX CFA 75MHZ 4IN 16SOIC RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 標準包裝:1,000 系列:- 應用:驅動器 輸出類型:差分 電路數:3 -3db帶寬:350MHz 轉換速率:1000 V/µs 電流 - 電源:14.5mA 電流 - 輸出 / 通道:60mA 電壓 - 電源，單路/雙路(±):5 V ~ 12 V，±2.5 V ~ 6 V 安裝類型:表面貼裝 封裝/外殼:20-VFQFN 裸露焊盤 供應商設備封裝:20-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) |
| LT1204CSW#PBF | 功能描述:IC VIDEOMUX CFA 75MHZ 4IN 16SOIC RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 視頻放大器和頻緩沖器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 應用:TFT-LCD 面板：VCOM 驅動器 輸出類型:滿擺幅 電路數:1 -3db帶寬:35MHz 轉換速率:40 V/µs 電流 - 電源:3.7mA 電流 - 輸出 / 通道:1.3A 電壓 - 電源，單路/雙路(±):9 V ~ 20 V，±4.5 V ~ 10 V 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬）裸露焊盤 供應商設備封裝:8-uMax-EP 包裝:管件 |
| LT1204CSW#PBF | 制造商:Linear Technology 功能描述:IC SM OP AMP VIDEO |
發布緊急采購，3分鐘左右您將得到回復。