- 您現在的位置：買賣IC網 > PDF目錄5892 > LT1206CS8#PBF (Linear Technology)IC CURRNT FEEDBK AMP 250MA 8SOIC PDF資料下載
參數資料
| 型號： | LT1206CS8#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 3/18頁 |
| 文件大小： | 0K |
| 描述： | IC CURRNT FEEDBK AMP 250MA 8SOIC |
| 標準包裝： | 100 |
| 放大器類型： | 電流反饋 |
| 電路數： | 1 |
| 轉換速率： | 900 V/µs |
| -3db帶寬： | 60MHz |
| 電流 - 輸入偏壓： | 10µA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 20mA |
| 電流 - 輸出 / 通道： | 1.2A |
| 電壓 - 電源，單路/雙路(±)： | 10 V ~ 30 V，±5 V ~ 15 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SO |
| 包裝： | 管件 |
| 產品目錄頁面： | 1317 (CN2011-ZH PDF) |
LT1206
11
1206fb
applicaTions inForMaTion
When the LT1206 is used to drive capacitive loads, the
available output current can limit the overall slew rate. In
the fastest configuration, the LT1206 is capable of a slew
rate of over 1V/ns. The current required to slew a capaci-
tor at this rate is 1mA per picofarad of capacitance, so
10,000pF would require 10A! The photo (Figure 6) shows
the large signal behavior with CL = 10,000pF. The slew rate
isabout60V/s,determinedbythecurrentlimitof600mA.
Differential Input Signal Swing
The differential input swing is limited to about ±6V by
an ESD protection device connected between the inputs.
In normal operation, the differential voltage between the
input pins is small, so this clamp has no effect; however,
in the shutdown mode the differential swing can be the
same as the input swing. The clamp voltage will then set
the maximum allowable input voltage. To allow for some
margin, it is recommended that the input signal be less
than ±5V when the device is shut down.
Capacitance on the Inverting Input
Currentfeedbackamplifiersrequireresistivefeedbackfrom
the output to the inverting input for stable operation. Take
care to minimize the stray capacitance between the output
and the inverting input. Capacitance on the inverting input
to ground will cause peaking in the frequency response
(and overshoot in the transient response), but it does not
degrade the stability of the amplifier.
Power Supplies
The LT1206 will operate from single or split supplies from
±5V (10V total) to ±15V (30V total). It is not necessary to
use equal value split supplies, however the offset voltage
and inverting input bias current will change. The offset
voltagechangesabout500Vpervoltofsupplymismatch.
The inverting bias current can change as much as 5A per
volt of supply mismatch, though typically the change is
less than 0.5A per volt.
Thermal Considerations
The LT1206 contains a thermal shutdown feature which
protectsagainstexcessiveinternal(junction)temperature.
If the junction temperature of the device exceeds the pro-
tection threshold, the device will begin cycling between
normal operation and an off state. The cycling is not
harmful to the part. The thermal cycling occurs at a slow
rate, typically 10ms to several seconds, which depends
on the power dissipation and the thermal time constants
of the package and heat sinking. Raising the ambient
temperature until the device begins thermal shutdown
gives a good indication of how much margin there is in
the thermal design.
For surface mount devices heat sinking is accomplished
by using the heat spreading capabilities of the PC board
and its copper traces. Experiments have shown that the
heat spreading copper layer does not need to be electri-
cally connected to the tab of the device. The PCB material
can be very effective at transmitting heat between the pad
area attached to the tab of the device, and a ground or
Figure 5c. Large-Signal Response, AV = 2
Figure 6. Large-Signal Response, CL = 10,000pF
RF = 750
RL = 50
20ns/DIV
1206 F05c
VS = ±15V
RL = RG = 3k
RL = ∞
500ns/DIV
1206 G06
相關PDF資料 |
PDF描述 |
|---|---|
| 929647-07-24-I | CONN HEADER .100 SNGL STR 24POS |
| 50NHG01B | FUSE 50A 500V CLASS GL/GG |
| TSW-132-23-S-D | CONN HEADER 64POS .100" DL GOLD |
| VS450C | GAS TRIGGER TUBE 450V CORE T&R |
| TSW-134-07-S-D | CONN HEADER 68POS .100" DL GOLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1206CS8TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:250mA/60MHz Current Feedback Amplifier |
| LT1206CT7 | 功能描述:IC CURR FEEDBK AMP 250MA TO220-7 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LT1206CT7#PBF | 功能描述:IC CURR FEEDBK AMP 250MA TO220-7 RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1206CY | 制造商:LINER 制造商全稱:Linear Technology 功能描述:250mA/60MHz Current Feedback Amplifier |
| LT1207 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:250mA/60MHz Current Feedback Amplifier Adjustable Supply Current |
發布緊急采購，3分鐘左右您將得到回復。