- 您現在的位置：買賣IC網 > PDF目錄5957 > LT1217CN8 (Linear Technology)IC CURRNT FEEDBCK AMP 10MHZ 8DIP PDF資料下載
參數資料
| 型號： | LT1217CN8 |
| 廠商： | Linear Technology |
| 文件頁數： | 6/8頁 |
| 文件大小： | 0K |
| 描述： | IC CURRNT FEEDBCK AMP 10MHZ 8DIP |
| 標準包裝： | 50 |
| 放大器類型： | 電流反饋 |
| 電路數： | 1 |
| 轉換速率： | 500 V/µs |
| -3db帶寬： | 10MHz |
| 電流 - 輸入偏壓： | 100nA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 1mA |
| 電流 - 輸出 / 通道： | 100mA |
| 電壓 - 電源，單路/雙路(±)： | 9 V ~ 36 V，±4.5 V ~ 18 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
LT1217
6
care to minimize the stray capacitance between the output
and the inverting input. Capacitance on the inverting input
to ground will cause peaking in the frequency response
(and overshoot in the transient response), but it does not
degrade the stability of the amplifier. The amount of
capacitance that is necessary to cause peaking is a func-
tion of the closed loop gain taken.
The higher the gain, the more capacitance is required to
cause peaking. We can add capacitance from the inverting
input to ground to increase the bandwidth in high gain
applications. For example, in this gain of 100 application,
the bandwidth can be increased from 1MHz to 2MHz by
adding a 2200pF capacitor.
LT1229 TA03
–
+
CG
RG
30
RF
3k
VOUT
LT1217
VIN
Boosting Bandwidth of High Gain Amplifier with
Capacitance on Inverting Input
FREQUENCY (Hz)
100k
35
GAIN
(dB)
37
38
40
42
43
45
1M
10M
LT1217 TA04
36
39
41
44
CG = 0
CG = 2200pF
CG = 4700pF
Capacitive Loads
The LT1217 can be isolated from capacitive loads with a
small resistor (10
to 20) or it can drive the capacitive
load directly if the feedback resistor is increased. Both
techniques lower the amplifier’s bandwidth about the
same amount. The advantage of resistive isolation is that
the bandwidth is only reduced when the capacitive load is
present. The disadvantage of resistor isolation is that
resistive loading causes gain errors. Because the DC
accuracy is not degraded with resistive loading, the de-
sired way of driving capacitive loads, such as flash
converters, is to increase the feedback resistor. The Maxi-
mum Capacitive Load versus Feedback Resistor curve
shows the value of feedback resistor and capacitive load
that gives 5dB of peaking. For less peaking, use a larger
feedback resistor.
Power Supplies
The LT1217 may be operated with single or split supplies
as low as
±4.5V (9V total) to as high as ±18V (36V total).
It is not necessary to use equal value split supplies,
however, the offset voltage will degrade about 350
V per
volt of mismatch. The internal compensation capacitor
decreases with increasing supply voltage. The –3dB Band-
width versus Supply Voltage curves show how this affects
the bandwidth for various feedback resistors. Generally,
the bandwidth at
±5V supplies is about half the value it is
at
±15V supplies for a given feedback resistor.
The LT1217 is very stable even with minimal supply
bypassing, however, the transient response will suffer if
the supply rings. It is recommended for good slew rate and
settling time that 4.7
F tantalum capacitors be placed
within 0.5 inches of the supply pins.
Input Range
The non-inverting input of the LT1217 looks like a 100M
resistor in parallel with a 3pF capacitor until the common
mode range is exceeded. The input impedance drops
somewhat and the input current rises to about 10
A when
the input comes too close to the supplies. Eventually,
when the input exceeds the supply by one diode drop, the
base collector junction of the input transistor forward
biases and the input current rises dramatically. The input
current should be limited to 10mA when exceeding the
supplies. The amplifier will recover quickly when the input
is returned to its normal common mode range unless the
input was over 500mV beyond the supplies, then it will
take an extra 100ns.
U
S
A
O
PPLICATI
WU
U
I FOR ATIO
相關PDF資料 |
PDF描述 |
|---|---|
| LT1920CS8#PBF | IC PREC INSTRUMNTATION AMP 8SOIC |
| LT1920CS8 | IC PREC INSTRUMNTATION AMP 8SOIC |
| SSQ-110-02-S-S | CONN RCPT .100" 10POS SNGL GOLD |
| LT1920CN8#PBF | IC PREC INSTRUMENTATION AMP 8DIP |
| LT1920CN8 | IC PREC INSTRUMENTATION AMP 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1217CN8#PBF | 功能描述:IC CURRNT FEEDBCK AMP 10MHZ 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:350 V/µs 增益帶寬積:180MHz -3db帶寬:320MHz 電流 - 輸入偏壓:12.5µA 電壓 - 輸入偏移:800µV 電流 - 電源:15mA 電流 - 輸出 / 通道:85mA 電壓 - 電源，單路/雙路(±):2.5 V ~ 12.6 V，±1.25 V ~ 6.3 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MSOP 包裝:帶卷 (TR) |
| LT1217CS8 | 功能描述:IC CURRNT FEEDBK AMP 10MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LT1217CS8#PBF | 功能描述:IC CURRNT FEEDBK AMP 10MHZ 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
| LT1217CS8#PBF | 制造商:Linear Technology 功能描述:IC OP-AMP 10MHZ 500V/ 1m 制造商:Linear Technology 功能描述:IC, OP-AMP, 10MHZ, 500V/s, 1mV, SOIC-8 |
| LT1217CS8#TR | 功能描述:IC AMP CURR FEEDBACK 10MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:30pA 電壓 - 輸入偏移:2000µV 電流 - 電源:200µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。