參數資料
型號: LT1259IS#PBF
廠商: Linear Technology
文件頁數: 10/12頁
文件大?。?/td> 0K
描述: IC AMP DUAL CURR FDBK SD 14SOIC
標準包裝: 55
放大器類型: 電流反饋
電路數: 2
轉換速率: 1600 V/µs
-3db帶寬: 130MHz
電流 - 輸入偏壓: 20µA
電壓 - 輸入偏移: 2000µV
電流 - 電源: 5mA
電流 - 輸出 / 通道: 60mA
電壓 - 電源,單路/雙路(±): 4 V ~ 30 V,±2 V ~ 15 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 14-SOIC(0.154",3.90mm 寬)
供應商設備封裝: 14-SO
包裝: 管件
7
LT1259/LT1260
Feedback Resistor Selection
The small-signal bandwidth of the LT1259/ LT1260 are set
by the external feedback resistors and the internal junction
capacitors. As a result, the bandwidth is a function of the
supply voltage, the value of the feedback resistor, the
closed-loop gain and the load resistor. The LT1259/LT1260
have been optimized for
±5V supply operation and have a
– 3dB bandwidth of 90MHz. See resistor selection guide in
Typical AC Performance table.
Capacitance on the Inverting Input
Current feedback amplifiers require resistive feedback
from the output to the inverting input for stable operation.
Take care to minimize the stray capacitance between the
output and the inverting input. Capacitance on the invert-
ing input to ground will cause peaking in the frequency
response (and overshoot in the transient response). See
the section on Demo Board Information.
Capacitive Loads
The LT1259/LT1260 can drive capacitive loads directly
when the proper value of feedback resistor is used. The
graph of Maximum Capacitive Load vs Feedback Resistor
should be used to select the appropriate value. The value
shown is for
≤5dB peaking when driving a 150 load at a
gain of 2. This is a worst case condition. The amplifier is
more stable at higher gains. Alternatively, a small resistor
(10
to 20) can be put in series with the output to isolate
the capacitive load from the amplifier output. This has the
advantage that the amplifier bandwidth is only reduced
when the capacitive load is present. The disadvantage is
that the gain is a function of the load resistance.
Power Supplies
The LT1259/LT1260 will operate from single or split
supplies from
±2V (4V total) to ±15V (30V total). It is not
necessary to use equal value split supplies, however the
offset voltage and inverting input bias current will change.
The offset voltage changes about 500
V per volt of
supply mismatch. The inverting bias current can change
as much as 5
A per volt of supply mismatch though
typically, the change is about 0.1
A per volt.
Slew Rate
The slew rate of a current feedback amplifier is not
independent of the amplifier gain configuration the way
slew rate is in a traditional op amp. This is because both the
input stage and the output stage have slew rate limitations.
In the inverting mode, and for higher gains in the nonin-
verting mode, the signal amplitude between the input pins
is small and the overall slew rate is that of the output stage.
For gains less than ten in the noninverting mode, the
overall slew rate is limited by the input stage.
EN
+IN
–IN
OUT
V+
V
LT1259/60 SS
, each amplifier
SI PLIFIED SCHE ATIC
WW
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料
PDF描述
MMS-114-01-T-DH CONN RCPT 2MM 28POS DL HORZ PCB
RMCF0805FT1K00 RES 1K OHM 1/8W 1% 0805 SMD
MMS-115-01-T-DH CONN RCPT 2MM 30POS DL HORZ PCB
MMS-116-01-T-DH CONN RCPT 2MM 32POS DL HORZ PCB
MMS-117-01-T-DH CONN RCPT 2MM 34POS DL HORZ PCB
相關代理商/技術參數
參數描述
LT125M 制造商:Thomas & Betts 功能描述:STR METALLIC CONNECTOR 制造商:Thomas & Betts 功能描述:Fittings Connector 1.25inch Female/Male Steel
LT125P 制造商:Thomas & Betts 功能描述:Fitting, Conduit; 1.257 in.; Nylon; Black; UL 94V2; 2.164 in. 制造商:Thomas & Betts 功能描述:ELECTRICAL CONDUIT FITTING 制造商:Thomas & Betts 功能描述:CONDUIT FITTING, STR, THERMOPLASTIC, BLK 制造商:Thomas & Betts 功能描述:CONDUIT FITTING, STR, THERMOPLASTIC, BLK, 31.75MM; Accessory Type:Straight Bullet Connector; Body Material:Thermoplastic; Color:Black; External Diameter:63.35mm; For Use With:Liquidtight Non-metallic XTRA FLEX Type B Conduit & Tubing;RoHS Compliant: Yes 制造商:Thomas & Betts 功能描述:Cable Accessories Fitting
LT1260 制造商:LINER 制造商全稱:Linear Technology 功能描述:Low Cost Dual and Triple 130MHz Current Feedback Amplifiers with Shutdown
LT1260CN 功能描述:IC AMP W/SHUTDOWN TRIPLE 16-DIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 5.5 V,±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR
LT1260CN#PBF 功能描述:IC AMP W/SHUTDOWN TRIPLE 16-DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:MicroAmplifier™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:3.5 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:5pA 電壓 - 輸入偏移:1500µV 電流 - 電源:220µA 電流 - 輸出 / 通道:60mA 電壓 - 電源,單路/雙路(±):4.5 V ~ 36 V,±2.25 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC(0.154",3.90mm 寬) 供應商設備封裝:14-SOIC 包裝:剪切帶 (CT) 其它名稱:296-29363-1