參數資料
型號: LT1312
廠商: Linear Technology Corporation
英文描述: PCMCIA Driver/Regulator(PCMCIA(個人計算機存儲卡國際協會)驅動器/穩壓器)
中文描述: PCMCIA驅動程序/穩壓器(使用PCMCIA(個人計算機存儲卡國際協會)驅動器/穩壓器)
文件頁數: 6/12頁
文件大小: 223K
代理商: LT1312
6
LT1312
Voltage Control Logic:
The LT1312 has five possible
output modes: 0V, 3.3V, 5V, 12V and Hi-Z. These five
modes are selected by the two Enable inputs and the V
CC
Sense input as described by the Truth Table.
V
CC
Sense Comparator:
When the V
CC
mode is selected,
the LT1312 automatically adjusts the regulated VPP
out-
put voltage to 3.3V or 5V depending upon the voltage
present at the PC card V
CC
supply pin. The threshold
voltage for the comparator is set at 4V and there is
approximately 50mV of hysteresis provided to ensure
clean switching between 3.3V and 5V.
VPP
VALID Comparator:
A voltage comparator monitors
the output voltage when the 12V mode is selected and is
driven low when the output is in regulation above 11V.
APPLICATIO
S I
N
FOR
ATIO
U
The LT1312 is a voltage programmable linear regulator
designed specifically for PCMCIA VPP driver applications.
The device operates with very low quiescent current
(30
μ
A) in the 0V and Hi-Z modes of operation. In the Hi-Z
mode, the output leakage current falls to 1
μ
A. Unloaded
quiescent current rises to only 55
μ
A and 75
μ
A when
programmed to 3.3V and 5V respectively. In addition to
the low quiescent currents, the LT1312 incorporates sev-
eral protection features which make it ideal for PCMCIA
applications. The LT1312 has built-in current limiting
(330mA) and thermal shutdown to protect the device and
the socket VPP pins against inadvertent short-circuit
conditions.
W
U
OPERATIO
The LT1312 is a programmable output voltage, low-
dropout linear regulator designed specifically for PCMCIA
VPP drive applications. Input power is typically obtained
from a loosely regulated input supply between 13V and
20V (see Applications Information section for more detail
on the input power supply). The LT1312 consists of the
following blocks:
Low Dropout Voltage Linear Regulator:
The heart of the
LT1312 is a PNP-based low-dropout voltage regulator
which drops the unregulated supply voltage from 13V to
20V down to 12V, 5V, 3.3V, 0V or Hi-Z depending upon the
state of the two Enable inputs and the V
CC
Sense input. The
regulator has built-in current limiting and thermal shut-
down to protect the device, the load, and the socket
against inadvertent short circuiting to ground.
U
AUXILIARY WINDING POWER SUPPLIES
Because the LT1312 provides excellent output regulation,
the input power supply may be loosely regulated. One
convenient (and economic) source of power is an auxiliary
winding on the main 5V switching regulator inductor in the
main system power supply.
LTC
1142HV Auxiliary Winding Power Supply
Figure 1 is a schematic diagram which describes how a
loosely regulated 14V power supply is created by adding
Burst Mode is a trademark of Linear Technology Corporation.
an auxiliary winding to the 5V inductor in a split 3.3V/5V
LTC1142HV power supply system. A turns ratio of 1:1.8 is
used for transformer T1 to ensure that the input voltage to
the LT1312 falls between 13V and 20V under all load
conditions. The 9V output from this additional winding is
rectified by diode D2, added to the main 5V output and
applied to the input of the LT1312. (Note that the auxiliary
winding must be phased properly as shown in Figure 1.)
The auxiliary winding is referenced to the 5V output which
provides DC current feedback from the auxiliary supply to
the main 5V section. The AC transient response is im-
proved by returning the negative lead of C5 to the 5V
output as shown.
When the 12V output is activated by a TTL high on the
Enable line, the 5V section of the LTC1142HV is forced into
continuous mode operation. A resistor divider composed
of R2, R3 and switch Q3 forces an offset which is sub-
tracted from the internal offset at the Sense
input (pin 14)
of the LTC1142HV. When this external offset cancels the
built-in 25mV offset, Burst Mode
TM
operation is inhibited
and the LTC1142HV is forced into continuous mode
operation. (See the LTC1142HV data sheet for further
detail). In this mode, the 14V auxiliary supply can be
相關PDF資料
PDF描述
LT1316CS8 Micropower DC/DC Converter with Programmable Peak Current Limit
LT1316CMS8 Micropower DC/DC Converter with Programmable Peak Current Limit
LT1316 8-Bit Identity/Magnitude Comparators (P=Q) with Enable 20-SOIC 0 to 70
LT1316IS8 SPDT, 1/4 Amp Two Circuit Pushbutton
LT1317BIS8 Micropower, 600kHz PWM DC/DC Converters
相關代理商/技術參數
參數描述
LT1312CS8 功能描述:IC DRVR/REG PCMCIA VPP SNGL8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器,DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP(0.173",4.40mm 寬) 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
LT1313 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual PCMCIA VPP Driver/Regulator
LT1313CS 功能描述:IC DRV/REG PCMCIA VPP DUAL16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器,DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP(0.173",4.40mm 寬) 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR)
LT1313CS#PBF 功能描述:IC DRV/REG PCMCIA VPP DL 16SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源,ICERA E400,E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA,WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR)
LT1313CS#TR 功能描述:IC DRIVER/REG VPP PCMCIA 16SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器,Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN(7x7) 包裝:管件