- 您現在的位置：買賣IC網 > PDF目錄377698 > LT1339ISW (LINEAR TECHNOLOGY CORP) High Power Synchronous DC/DC Controller PDF資料下載
參數資料
| 型號： | LT1339ISW |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | High Power Synchronous DC/DC Controller |
| 中文描述： | SWITCHING CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | 0.300 INCH, PLASTIC, SO-20 |
| 文件頁數： | 7/20頁 |
| 文件大?。?/td> | 415K |
| 代理商： | LT1339ISW |
7
LT1339
SYNC (Pin 1):
Oscillator Synchronization Pin with TTL-
Level Compatible Input. Input drives internal rising edge
triggered one-shot; sync signal on/off times should be
≥
1
μ
s (10% to 90% DC at 100kHz). Does not contain
internal pull-up. Connect to SGND if not used.
5V
REF
(Pin 2):
5V Output Reference. Allows connection
of external loads up to 10mA DC. (Reference is not
available in shutdown.) Typically bypassed with 1
μ
F
capacitor to SGND.
CT (Pin 3):
Oscillator Timing Pin. Connect a capacitor
(C
CT
) to ground and a pull-up resistor (R
CT
) to the 5V
REF
supply. Typical values are CT = 1000pF and 10k
≤
R
CT
≤
30k.
SL/ADJ (Pin 4):
Slope Compensation Adjustment.
Allows increased slope compensation for certain high
duty cycle applications. Resistive loading of the pin
increases effective slope compensation. A resistor
divider from the 5V
REF
pin can tailor the onset of addi-
tional slope compensation to specific regions in each
switch cycle. Pin can be floated or connected to 5V
REF
if
no additional slope compensation is required. (See
Applications Information section for slope compensa-
tion details.)
I
AVG
(Pin 5):
Average Current Limit Integration. Fre-
quency response characteristic is set using the 50k
output impedance and external capacitor to ground.
Averaging roll-off typically set at 1 to 2 orders of magni-
tude under switching frequency. (Typical capacitor value
~1000pF for f
O
= 100kHz.) Shorting this pin to SGND will
disable the average current limit function.
SS (Pin 6):
Soft Start. Generates ramping threshold for
regulator current limit during start-up and after UVLO
event by sourcing about 8
μ
A into an external capacitor.
V
C
(Pin 7):
Error Amplifier Output. RC load creates
dominant compensation in power supply regulation feed-
back loop to provide optimum transient response. (See
Applications Information section for compensation de-
tails.)
SGND (Pin 8):
Small-Signal Ground. Connect to negative
terminal of C
OUT
.
V
FB
(Pin 9):
Error Amplifier Inverting Input. Used as
voltage feedback input node for regulator loop. Pin
sources about 0.5
μ
A DC bias current to protect from an
open feedback path condition.
PI
FU
CTIO
N
S
U
U
V
REF
(Pin 10):
Bandgap Generated Voltage Reference
Decoupling. Connect a capacitor to signal ground. (Typi-
cal capacitor value ~0.1
μ
F.)
SENSE
+
(Pin 11):
Current Sense Amplifier Inverting
Input. Connect to most positive (DC) terminal of current
sense resistor.
SENSE
–
(Pin 12):
Current Sense Amplifier Noninverting
Input. Connect to most negative (DC) terminal of current
sense resistor.
RUN/SHDN (Pin 13):
Precision Referenced Shutdown.
Can be used as logic level input for shutdown control or
as an analog monitor for input supply undervoltage
protection, etc. IC is enabled when RUN/SHDN pin rising
edge exceeds 1.25V. About 25mV of hysteresis helps
assure stable mode switching. All internal functions are
disabled in shutdown mode. If this function is not
desired, connect RUN/SHDN to 12V
IN
(typically through
a 100k resistor). See Applications Information section.
PHASE (Pin 14):
Output Driver Phase Control. If Pin 14
is not connected (floating), the topside driver operates
the main switch, with the bottom side driver operating
the synchronous switch. Shorting Pin 14 to ground
reverses the roles of the output drivers. PHASE is typi-
cally shorted to ground for inverting and boost configu-
rations. Positive buck configuration requires the PHASE
pin to float. See Applications Information section.
PGND (Pin 15):
Power Ground. References the bottom
side output switch and internal driver control circuits.
Connect with low impedance trace to V
IN
decoupling
capacitor negative (ground) terminal.
BG (Pin 16):
Bottom Side Output Driver. Connects to gate
of bottom side external power FET.
12V
IN
(Pin 17):
12V Power Supply Input. Bypass with at
least 1
μ
F to PGND.
TS (Pin 18):
Boost Output Driver Reference. Typically
connects to source of topside external power FET and
inductive switch node.
TG (Pin 19):
Topside (Boost) Output Driver. Connects to
gate of topside external power FET.
V
BOOST
(Pin 20):
Topside Power Supply. Bootstrapped
via 1
μ
F capacitor tied to switch node (Pin 18) and
Schottky diode connected to the 12V
IN
supply.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1341 | 5V RS232 Transceiver with One Receiver Active in Shutdown |
| LT1341C | Octal Buffers/Drivers With 3-State Outputs 20-PDIP 0 to 70 |
| LT1341CG | Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 |
| LT1341CNW | Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 |
| LT1341CSW | Octal Buffers/Drivers With 3-State Outputs 20-SO 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1339ISW#PBF | 功能描述:IC REG CTRLR BST PWM CM 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LT1339ISW#TR | 功能描述:IC REG CTRLR BST PWM CM 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT1339ISW#TRPBF | 功能描述:IC REG CTRLR BST PWM CM 20-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LT1339ISWPBF | 制造商:Linear Technology 功能描述:DC-DC Controller High Power Synch. SO20W |
| LT133X1-104 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:18+18 Dual channel 5V LVDS |
發布緊急采購，3分鐘左右您將得到回復。