- 您現在的位置：買賣IC網 > PDF目錄385500 > LT1357CN8 (LINEAR TECHNOLOGY CORP) Octal Buffers And Line Drivers With 3-State Outputs 20-SO 0 to 70 PDF資料下載
參數資料
| 型號： | LT1357CN8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | Octal Buffers And Line Drivers With 3-State Outputs 20-SO 0 to 70 |
| 中文描述： | OP-AMP, 600 uV OFFSET-MAX, 25 MHz BAND WIDTH, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 288K |
| 代理商： | LT1357CN8 |
10
LT1357
APPLICATIO
S I
FOR
ATIO
U
series with the output. The other end of the cable should
be terminated with the same value resistor to ground.
W
U
U
Input Considerations
Each of the LT1357 inputs is the base of an NPN and
a PNP transistor whose base currents are of opposite
polarity and provide first-order bias current cancellation.
Because of variation in the matching of NPN and PNP
beta, the polarity of the input bias current can be positive
or negative. The offset current does not depend on
NPN/PNP beta matching and is well controlled. The use of
balanced source resistance at each input is recommended
for applications where DC accuracy must be maximized.
The inputs can withstand transient differential input volt-
ages up to 10V without damage and need no clamping or
source resistance for protection. Differential inputs, how-
ever, generate large supply currents (tens of mA) as
required for high slew rates. If the device is used with
sustained differential inputs, the average supply current
will increase, excessive power dissipation will result and
the part may be damaged. The part should not be used as
a comparator, peak detector or other open-loop applica-
tion with large, sustained differential inputs Under
normal, closed-loop operation, an increase of power
dissipation is only noticeable in applications with large
slewing outputs and is proportional to the magnitude of
the differential input voltage and the percent of the time
that the inputs are apart. Measure the average supply
current for the application in order to calculate the power
dissipation.
Power Dissipation
The LT1357 combines high speed and large output drive
in a small package. Because of the wide supply voltage
range, it is possible to exceed the maximum junction
temperature under certain conditions. Maximum junction
temperature (T
J
) is calculated from the ambient tempera-
ture (T
A
) and power dissipation (P
D
) as follows:
LT1357CN8: T
J
= T
A
+ (P
D
130
°
C/W)
LT1357CS8: T
J
= T
A
+ (P
D
190
°
C/W)
Worst-case power dissipation occurs at the maximum
supply current and when the output voltage is at 1/2 of
either supply voltage (or the maximum swing if less than
1/2 supply voltage). Therefore P
DMAX
is:
P
DMAX
= (V
+
– V
–
)(I
SMAX
) + (V
+
/2)
2
/R
L
Example: LT1357CS8 at 70
°
C, V
S
=
±
15V, R
L
= 120
(Note: the minimum short-circuit current at 70
°
C is
25mA, so the output swing is guaranteed only to 3V with
120
.)
P
DMAX
= (30V 2.9mA) + (15V–3V)(25mA) = 387mW
T
JMAX
= 70
°
C + (387mW 190
°
C/W) = 144
°
C
Circuit Operation
The LT1357 circuit topology is a true voltage feedback
amplifier that has the slewing behavior of a current feed-
back amplifier. The operation of the circuit can be under-
stood by referring to the simplified schematic. The inputs
are buffered by complementary NPN and PNP emitter
followers which drive a 500
resistor. The input voltage
appears across the resistor generating currents which are
mirrored into the high impedance node. Complementary
followers form an output stage which buffers the gain
node from the load. The bandwidth is set by the input
resistor and the capacitance on the high impedance node.
The slew rate is determined by the current available to
charge the gain node capacitance. This current is the
differential input voltage divided by R1, so the slew rate
is proportional to the input. Highest slew rates are there-
fore seen in the lowest gain configurations. For example,
a 10V output step in a gain of 10 has only a 1V input step,
whereas the same output step in unity-gain has a ten times
greater input step. The curve of Slew Rate vs Input Level
illustrates this relationship. The LT1357 is tested for slew
rate in a gain of –2 so higher slew rates can be expected
in gains of 1 and –1, and lower slew rates in higher gain
configurations.
The RC network across the output stage is bootstrapped
when the amplifier is driving a light or moderate load and
相關PDF資料 |
PDF描述 |
|---|---|
| LT1357CS8 | Octal Buffers And Line Drivers With 3-State Outputs 20-SO 0 to 70 |
| LT1361 | OCTAL BUFFERS AND LINE DRIVERS 20-SOIC 0 to 70 |
| LT1361CN8 | OCTAL BUFFERS AND LINE DRIVERS 20-PDIP 0 to 70 |
| LT1361CS8 | OCTAL BUFFERS AND LINE DRIVERS 20-PDIP 0 to 70 |
| LT1362 | OCTAL BUFFERS AND LINE DRIVERS 20-SO 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1357CN8#PBF | 功能描述:IC OP-AMP HI-SPD 25MHZ SNGL 8DIP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:C-Load™ 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1357CS8 | 功能描述:IC OP-AMP HISPD 25MHZ SNGL 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:C-Load™ 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:3 V/µs 增益帶寬積:10MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:70µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:48mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:Digi-Reel® 其它名稱:MAX4475AUT#TG16DKR |
| LT1357CS8#PBF | 功能描述:IC OP-AMP HISPD 25MHZ SNGL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:C-Load™ 標準包裝:2,500 系列:- 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:45nA 電壓 - 輸入偏移:2000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:40mA 電壓 - 電源，單路/雙路(±):3 V ~ 32 V，±1.5 V ~ 16 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:14-TSSOP 包裝:帶卷 (TR) 其它名稱:LM324ADTBR2G-NDLM324ADTBR2GOSTR |
| LT1357CS8#TR | 功能描述:IC OPAMP 25MHZ HI SPEED LP 8SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:C-Load™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:電流檢測 電路數:1 輸出類型:- 轉換速率:- 增益帶寬積:125kHz -3db帶寬:- 電流 - 輸入偏壓:- 電壓 - 輸入偏移:100µV 電流 - 電源:1.1µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-WFBGA，CSPBGA 供應商設備封裝:4-UCSP（2x2） 包裝:剪切帶 (CT) 其它名稱:MAX9634WERS+TCT |
| LT1357CS8#TRPBF | 功能描述:IC OP-AMP HISPD 25MHZ SNGL 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:C-Load™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 放大器類型:電流檢測 電路數:1 輸出類型:- 轉換速率:- 增益帶寬積:125kHz -3db帶寬:- 電流 - 輸入偏壓:- 電壓 - 輸入偏移:100µV 電流 - 電源:1.1µA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:4-WFBGA，CSPBGA 供應商設備封裝:4-UCSP（2x2） 包裝:剪切帶 (CT) 其它名稱:MAX9634WERS+TCT |
發布緊急采購，3分鐘左右您將得到回復。