- 您現在的位置：買賣IC網 > PDF目錄377700 > LT1373CS8 (LINEAR TECHNOLOGY CORP) Synchronous 4-Bit Up/Down Binary Counters With 3-State Outputs 20-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | LT1373CS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Synchronous 4-Bit Up/Down Binary Counters With 3-State Outputs 20-SOIC 0 to 70 |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 275 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | 0.150 INCH, PLASTIC, SO-8 |
| 文件頁數： | 8/12頁 |
| 文件大小： | 181K |
| 代理商： | LT1373CS8 |
8
LT1373
component height, output voltage ripple, EMI, fault cur-
rent in the inductor, saturation, and of course, cost. The
following procedure is suggested as a way of handling
these somewhat complicated and conflicting requirements.
1. Assume that the average inductor current (for a boost
converter) is equal to load current times V
OUT
/V
IN
and
decide whether or not the inductor must withstand
continuous overload conditions. If average inductor
current at maximum load current is 0.5A, for instance,
a 0.5A inductor may not survive a continuous 1.5A
overload condition. Also, be aware that boost convert-
ers are not short-circuit protected, and that under
output short conditions, inductor current is limited only
by the available current of the input supply.
2. Calculate peak inductor current at full load current to
ensure that the inductor will not saturate. Peak current
can be significantly higher than output current, espe-
cially with smaller inductors and lighter loads, so don’t
omit this step. Powered iron cores are forgiving be-
cause they saturate softly, whereas ferrite cores satu-
rate abruptly. Other core materials fall in between
somewhere. The following formula assumes continu-
ous mode operation, but it errors only slightly on the
high side for discontinuous mode, so it can be used for
all conditions.
I
PEAK
= I
OUT
V
IN
= minimum input voltage
f = 250kHz switching frequency
+
V
OUT
V
IN
V
IN
(V
OUT
–
V
IN
)
2(f)(L)(V
OUT
)
3. Decide if the design can tolerate an “open” core geom-
etry like a rod or barrel, which have high magnetic field
radiation, or whether it needs a closed core like a toroid
to prevent EMI problems. One would not want an open
core next to a magnetic storage media for instance!
This is a tough decision because the rods or barrels are
temptingly cheap and small, and there are no helpful
guidelines to calculate when the magnetic field radia-
tion will be a problem.
4. Start shopping for an inductor which meets the require-
ments of core shape, peak current (to avoid saturation),
average current (to limit heating), and fault current, (if the
inductor gets too hot, wire insulation will melt and cause
turn-to-turn shorts). Keep in mind that all good things
like high efficiency, low profile and high temperature
operation will increase cost, sometimes dramatically.
5. After making an initial choice, consider the secondary
things like output voltage ripple, second sourcing, etc.
Use the experts in the Linear Technology application
department if you feel uncertain about the final choice.
They have experience with a wide range of inductor
types and can tell you about the latest developments in
low profile, surface mounting, etc.
Output Capacitor
The output capacitor is normally chosen by its effective
series resistance (ESR), because this is what determines
output ripple voltage. At 500kHz, any polarized capacitor
is essentially resistive. To get low ESR takes volume so
physically smaller capacitors have high ESR. The ESR
range for typical LT1373 applications is 0.05
to 0.5
. A
typical output capacitor is an AVX type TPS, 22
μ
F at 25V,
with a guaranteed ESR less than 0.2
. This is a “D” size
surface mount solid tantalum capacitor. TPS capacitors
are specially constructed and tested for low ESR, so they
give the lowest ESR for a given volume. To further reduce
ESR, multiple output capacitors can be used in parallel.
The value in microfarads is not particularly critical and
values from 22
μ
F to greater than 500
μ
F work well, but you
cannot cheat mother nature on ESR. If you find a tiny 22
μ
F
solid tantalum capacitor, it will have high ESR and output
ripple voltage will be terrible. Table 1 shows some typical
solid tantalum surface mount capacitors.
Table 1. Surface Mount Solid Tantalum Capacitor
ESR and Ripple Current
E CASE SIZE
AVX TPS, Sprague 593D
AVX TAJ
D CASE SIZE
AVX TPS, Sprague 593D
AVX TAJ
C CASE SIZE
AVX TPS
AVX TAJ
B CASE SIZE
AVX TAJ
ESR (MAX
)
0.1 to 0.3
0.7 to 0.9
RIPPLE CURRENT (A)
0.7 to 1.1
0.4
0.1 to 0.3
0.9 to 2.0
0.7 to 1.1
0.36 to 0.24
0.2 (Typ)
1.8 to 3.0
0.5 (Typ)
0.22 to 0.17
2.5 to 10
0.16 to 0.08
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LT1373HVIN8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1373HVIS8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1373HVCN8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1373HVCS8 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT1373 | 250kHz Low Supply Current High Efficiency 1.5A Switching Regulator(250kHz ，低電源電流1.5A,高效率開關穩壓器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1373CS8#/PBF | 制造商:Linear Technology 功能描述: |
| LT1373CS8#PBF | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1373CS8#TR | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
| LT1373CS8#TR/PBF | 制造商:Linear Technology 功能描述: |
| LT1373CS8#TRPBF | 功能描述:IC REG MULTI CONFIG ADJ 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤 |
發布緊急采購，3分鐘左右您將得到回復。