- 您現在的位置：買賣IC網 > PDF目錄385501 > LT1470 (Linear Technology Corporation) Single and Dual PCMCIA Protected 3.3V/5V VCC Switches PDF資料下載
參數資料
| 型號： | LT1470 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Single and Dual PCMCIA Protected 3.3V/5V VCC Switches |
| 中文描述： | 單路和雙路的PCMCIA保護3.3V/5V的虛擬通道連接開關 |
| 文件頁數： | 4/12頁 |
| 文件大小： | 229K |
| 代理商： | LT1470 |
4
LTC1470/LTC1471
TYPICAL PERFOR
M
A
CE CHARACTERISTICS
U
PI
FU
CTIO
N
S
U
U
LTC1470
OUT (Pins 1, 8):
Output Pins. The outputs of the LTC1470
are switched between three operating states: OFF, 3.3V
and 5V. These pins are protected against accidental short
circuits to ground by SafeSlot current limit circuitry which
protects the socket, the card, and the system power
supplies against damage. A second level of protection is
provided by thermal shutdown circuitry which protects
both switches against over-temperature conditions.
5V
IN
(Pin 2):
5V
Input Supply Pin. The 5V
IN
supply pin
serves two purposes. The first purpose is as the power
supply input for the 5V NMOS switch. The second purpose
is to provide power for the input, gate drive, and protection
circuitry for both the 3.3V and 5V V
CC
switches. This pin
must therefore be continuously powered.
EN1, EN0 (Pins 3, 4):
Enable Inputs. The two V
CC
Enable
inputs are designed to interface directly with industry
standard PCMCIA controllers and are high impedance
CMOS gates with ESD protection diodes to ground, and
should not be forced below ground. Both inputs have
about 100mV of built-in hysteresis to ensure clean switch-
ing between operating modes. The LTC1470 is designed
to operate without12V power. The gates of the V
CC
NMOS
switches are powered by charge pumps from the 5V
IN
supply pins (see Applications Information section for
more detail). The Enable inputs should be turned off (both
asserted high or both asserted low) at least 100
μ
s before
the 5V
IN
power is removed to ensure that both V
CC
NMOS
switch gates are fully discharged and both switches are in
the high impedance mode.
GND (Pin 5):
Ground Connection.
3V
IN
(Pins 6, 7):
3V
Input Supply Pins. The 3V
IN
supply
pins serve as the power supply input for the 3.3V switches.
These pins do not provide any power to the internal control
circuitry and therefore do not consume any power when
unloaded or turned off.
JUNCTION TEMPERATURE (
°
C)
0
0
5
)
0.05
0.10
0.15
0.20
0.25
0.30
25
50
75
100
1470/71 G06
125
PROGRAMMED
TO 5V
5V Switch Resistance
TIME (ms)
–0.2
I
O
0
1
1.4
1470/71 G08
6
4
0
0.2
0.6
1.0
2
3
2
0
0.4
0.8
1.2
C
OUT
= 15
μ
F
R
OUT
= 10
T
J
= 25
°
C
CURRENT
LIMITED
C
OUT
= 150
μ
F
OUT
= 10
Inrush Current (5V Switch)
Inrush Current (3.3V Switch)
TIME (ms)
–0.2
I
O
0
1
1.4
1470/71 G09
6
4
0
0.2
0.6
1.0
2
3
2
0
0.4
0.8
1.2
T
J
= 25
°
C
C
OUT
= 15
μ
F
R
OUT
= 6.6
C
OUT
= 150
μ
F
R
OUT
= 6.6
C
OUT
= 150
μ
F
R
OUT
= 6.6
(LTC1470 or 1/2 LTC1471)
相關PDF資料 |
PDF描述 |
|---|---|
| LT1490A | Dual Micropower Rail-to-Rail Input and Output Op Amps(雙路微功耗，滿幅度輸入和輸出運算放大器) |
| LT1491A | Quad Micropower Rail-to-Rail Input and Output Op Amps(四路微功耗，滿幅度輸入和輸出運算放大器) |
| LT1492 | 5MHz, 3V/us, Low Power Single Supply, Dual and Quad Precision Op Amps |
| LT1492CN8 | 5MHz, 3V/us, Low Power Single Supply, Dual and Quad Precision Op Amps |
| LT1492CS8 | 5MHz, 3V/us, Low Power Single Supply, Dual and Quad Precision Op Amps |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1474M | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Dot Matrix LED Unit for Outdoor Use (Lamp Type,Water-proof Type) |
| LT1483 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultra-Low Power RS485 Low EMI Transceiver with Shutdown |
| LT1483CSA | 制造商:Linear Technology 功能描述:OBSOLETE/ DISCONTINUED |
| LT1485 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Differential Bus Transceiver |
| LT1490 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual and Quad Micropower Rail-to-Rail Input and Output Op Amps |
發布緊急采購，3分鐘左右您將得到回復。