參數資料
型號： LT1507C
廠商： Linear Technology Corporation
元件分類： 基準電壓源/電流源
英文描述： RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
中文描述： 抗輻射高效，5安培開關穩壓器
文件頁數： 14/20頁
文件大小： 343K
代理商： LT1507C
14
LT1507
APPLICATIO
S I
FOR
ATIO
U
high speed circulating current path shown in Figure 4 and
to make connections to the output capacitor in a manner
that minimizes output ripple and noise. For more details,
see Applications Information section in the LT1376 data
sheet.
W
U
U
LT1507 F04
5V
L1
V
IN
HIGH
FREQUENCY
CIRCULATING
PATH
LOAD
SWITCH NODE
C
3
C
1
INPUT BYPASSING AND VOLTAGE RANGE
Input Bypass Capacitor
Stepdown converters draw current from the input supply
in pulses. The average height of these pulses is equal to
load current and the duty cycle is equal to V
OUT
/V
IN
. Rise
and fall time of the current is very fast. A local bypass
capacitor across the input supply is necessary to ensure
proper operation of the regulator and minimize the ripple
current fed back into the input supply. The capacitor also
forces switching current to flow in a tight local loop,
minimizing EMI.
Do not cheat on the ripple current rating of the input
bypass capacitor, but also don’t get hung up on the value
in microfarads. The input capacitor is intended to absorb
all the switching current ripple, which can have an RMS
value as high as one half of load current. Ripple current
ratings on the capacitor must be observed to ensure
reliable operation. The actual value of the capacitor in
microfarads is not particularly important because at
500kHz, any value above 5
μ
F is essential resistive. Ripple
current rating is the critical parameter. RMS ripple current
can be calculated from:
I
RMS
(
I
V
V
V
V
RIPPLE
OUT
OUT
IN
OUT
IN
)
(
–
2
)
=
Figure 4. High Speed Switching Path
The term inside the radical has a maximum value of 0.5
when input voltage is twice output and stays near 0.5 for
a relatively wide range of input voltages. It is common
practice, therefore, to simply use the worst-case value and
assume that RMS ripple current is one half of load current.
At maximum output current of 1.5A for the LT1507, the
input bypass capacitor should be rated at 0.75A ripple
current. Note however, that there are many secondary
considerations in choosing the final ripple current rating.
These include ambient temperature, average versus peak
load current, equipment operating schedule and required
product lifetime. For more details see Application Notes 19
and 46.
Input Capacitor Type
Some caution must be used when selecting the type of
capacitor used at the input of regulators. Aluminum
electrolytics are lowest cost, but are physically large to
achieve adequate ripple current rating, and size con-
straints (especially height) may preclude their use.
Ceramic capacitors are now available in larger values and
their high ripple current and voltage rating make them
ideal for input bypassing. Cost is slightly higher and
footprint may also be somewhat larger. Solid tantalum
capacitors are a good choice except that they have a
history of occasional spectacular failures when they are
subjected to very large current surges during power-up.
The capacitors can short and then burn with a brilliant
white light and lots of nasty smoke. This phenomenon
occurs in only a small percentage of units, but it has led
some OEM companies to forbid their use in high surge
applications. The input bypass capacitor of regulators can
see such high surges when a battery or high capacitance
source is connected.
Several manufacturers have developed a line of solid
tantalum capacitors specially tested for surge capability
(AVX TPS series for instance, see Table 2). Even these
units may fail if the input current surge exceeds a value
equal to the voltage rating of the capacitor divided by 1
(10A for a 10V capacitor). For this reason, AVX recom-
mends using the highest voltage rating possible for the
input capacitor. For equal case size this means that lower
values of capacitance must be used. As stated above, this
相關PDF資料
PDF描述
LT1507CN8 Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 24-SOIC 0 to 70
LT1507CN8-3.3 Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 24-SOIC 0 to 70
LT1507CS8 RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
LT1507CS8-3.3 Octal D-Type Edge-Triggered Flip-Flops With 3-State Outputs 24-SO 0 to 70
LT1507I RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS
相關代理商/技術參數
參數描述
LT1507CN8 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT1507CN8#PBF 功能描述:IC REG BUCK ADJ 1.5A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:20 系列:SIMPLE SWITCHER® 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:12V 輸入電壓:4 V ~ 60 V PWM 型:電壓模式 頻率 - 開關:52kHz 電流 - 輸出:1A 同步整流器:無 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:16-DIP（0.300"，7.62mm） 包裝:管件 供應商設備封裝:16-DIP 其它名稱:*LM2575HVN-12LM2575HVN-12
LT1507CN8-3.3 功能描述:IC REG BUCK 3.3V 1.5A 8DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V，1.5V，1.8V，2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT1507CN8-3.3#PBF 功能描述:IC REG BUCK 3.3V 1.5A 8DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2
LT1507CS8 功能描述:IC REG BUCK ADJ 1.5A 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*