參數資料
型號： LT1567CMS8#TR
廠商： Linear Technology
文件頁數： 2/16頁
文件大?。?/td> 0K
描述： IC OPAMP/INV BUILDNG BLOCK 8MSOP
標準包裝： 2,500
類型： ADC 驅動器
應用： 濾波器
安裝類型： 表面貼裝
封裝/外殼： 8-TSSOP，8-MSOP（0.118"，3.00mm 寬）
供應商設備封裝： 8-MSOP
包裝： 帶卷 (TR)
其它名稱： LT1567CMS8TR
LT1567
10
1567fa
APPLICATIO S I FOR ATIO
WU
U
output from the INV block (Pin 7). These two outputs
maintain equal gain and 180 phase shift over a wide
frequency range. This feature permits choosing the signal
polarity in single ended applications, and also performs
single ended to differential conversion. The latter property
is useful as an antialiasing filter to drive standard mono-
lithic A/D converters having differential inputs, as illus-
trated on the first page of this data sheet.
Dealing with High Source Impedances
The voltage VIN in Figure 1, on the left side of R1, is the
signal voltage that the filter sees. If a voltage source with
significant internal impedance drives the VIN node in
Figure 1, then the filter input VIN may differ from the
source’s open-circuit output, and the difference can be
complex, because the filter presents a complex imped-
ance to VIN. A rule of thumb is that a source impedance is
negligibly “l(fā)ow” if it is much smaller than R1 at frequencies
of interest. Otherwise, the source impedance (resistive or
reactive) effectively adds to R1 and may change the signal
frequency response compared to that with a low source
impedance. If the source is resistive and predictable, then
it may be possible to design for it by reducing R1.
Unpredictable or nonresistive source impedances that are
not much less than R1 should be buffered.
Construction and Instrumentation Cautions
Electrically clean construction is important in applica-
tions seeking the full dynamic range and bandwidth of the
LT1567. Using the shortest possible wiring or printed-
circuit paths will minimize parasitic capacitance and
inductance. High quality supply bypass capacitors of
0.1
F near the chip, connected to a ground plane, provide
good decoupling from a clean, low inductance power
source. But several inches of wire (i.e., a few microhenrys
of inductance) from the power supplies, unless decoupled
by substantial capacitance (
≥10F) near the chip, can
cause a high Q LC resonance in the hundreds of kHz in the
chip’s supplies or ground reference. This may impair filter
performance at those frequencies. In stringent filter
applications, a compact, carefully laid out printed circuit
board with good ground plane makes a difference in both
stopband rejection and distortion. Finally, equipment to
measure filter performance can itself introduce distortion
or noise. Checking for these limits with a wire in place of
the filter is a prudent routine procedure.
Low Noise Differential Circuits
The LT1567 is an optimum analog building for designing
single supply differential circuits to process low level
signals. Figure 3 shows a single ended to differential
amplifier driving a 1st order differential RC filter. The
differential output of Figure 3 is a function of input (VIN)
and the VREF voltage on Pin 5. (The range of the VREF
voltage on Pin 5 in Figures 3, 4 and 5 is the common mode
input voltage range parameter under Electrical
Characteristics.)The graph of Figure 3 shows the differen-
tial signal-to-noise ratio for a gain of 2 and a gain of 10.
Increasing the differential gain increases the differential
signal-to-noise ratio. The equivalent input noise is equal to
the output noise divided by the gain. For example, with a
gain equal to 2 (R2 = R1 = 200
) and a gain equal to 10
(R2 = 1k, R1 = 200
),theequivalentinputnoiseis4.59nV/
√Hz and 2.04nV/√Hz respectively. The VREF voltage on Pin
5 can be set by a voltage divider or a reference voltage
source. To maximize the unclipped LT1567 output swing,
the DC output voltage should be set at V+/2. However, if
VINDC (the input DC voltage) is within the range of VREF,
then VREF can be equal to VINDC. The input signal can also
be AC coupled to the input resistor, R1, and VREF set to the
DC voltage of the circuit following the amplifier. For
example, VREF might be set to 1.2V to bias the input of an
I and Q modulator used in broadband communication
systems.
相關PDF資料
PDF描述
VI-250-IV-F1 CONVERTER MOD DC/DC 5V 150W
LTC1541IS8#PBF IC OPAMP/COMP/REF MICRPWR 8SOIC
VE-2TN-IV-F4 CONVERTER MOD DC/DC 18.5V 150W
LTC1541IS8 IC OPAMP/COMP/REF MICRPWR 8SOIC
LT1567CMS8 IC OPAMP/INV BUILDNG BLOCK 8MSOP
相關代理商/技術參數
參數描述
LT1567IMS8 功能描述:IC BLOCK BUILD FLTR LONOIS 8MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT1567IMS8#PBF 功能描述:IC BLOCK BUILD FLTR LONOIS 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT1567IMS8#TR 功能描述:IC BLOCK BUILD FLTR LONOIS 8MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT1567IMS8#TRPBF 功能描述:IC BLOCK BUILD FLTR LONOIS 8MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 放大器 - 專用 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:60 系列:- 類型:可變?cè)鲆娣糯笃?應用:CATV 安裝類型:表面貼裝 封裝/外殼:20-WQFN 裸露焊盤 供應商設備封裝:20-TQFN-EP（5x5） 包裝:托盤
LT1568 制造商:LINER 制造商全稱:Linear Technology 功能描述:Very Low Noise, High Frequency Active RC, Filter Building Block
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*