- 您現在的位置：買賣IC網 > PDF目錄377709 > LT1584CT (LINEAR TECHNOLOGY CORP) 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed PDF資料下載
參數資料
| 型號： | LT1584CT |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed |
| 中文描述： | ADJUSTABLE POSITIVE LDO REGULATOR, 1.45 V DROPOUT, PSFM3 |
| 封裝： | PLASTIC, TO-220, 3 PIN |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 276K |
| 代理商： | LT1584CT |
10
LT1584/LT1585/LT1587
APPLICATIO
S I
N
FOR
ATIO
U
load current of 10mA. The current out of the adjust pin adds
to the current from R1 and is typically 55
μ
A. Its output
voltage contribution is small and only needs consideration
when very precise output voltage setting is required.
W
U
LT1584
ADJ
V
IN
V
OUT
IN
R1
V
REF
R2
V
OUT
= V
REF
(1 + R2/R1) + I
ADJ
(R2)
OUT
I
ADJ
55
μ
A
LT1585 F03
C1
10
μ
F
+
C2
22
μ
F
+
Figure 3. Basic Adjustable Regulator
Load Regulation
It is not possible to provide true remote load sensing
because the LT1584/LT1585/LT1587 are three-terminal
devices. Load regulation is limited by the resistance of the
wire connecting the regulators to the load. Load regulation
per the data sheet specification is measured at the bottom
of the package.
For fixed voltage devices, negative side sensing is a true
Kelvin connection with the ground pin of the device re-
turned to the negative side of the load. This is illustrated in
Figure 4.
LT1584-3.3
R
PARASITIC
LINE RESISTANCE
GND
V
IN
R
L
IN
OUT
LT1585 F04
Figure 4. Connection for Best Load Regulation
For adjustable voltage devices, negative side sensing is a
true Kelvin connection with the bottom of the output divider
returned to the negative side of the load. The best load
regulation is obtained when the top of resistor divider R1
connects directly to the regulator output and not to the
load. Figure 5 illustrates this point. If R1 connects to the
load, the effective resistance between the regulator and the
load is:
R
P
×
(1 + R2/R1), R
P
= Parasitic Line Resistance
The connection shown in Figure 5 does not multiply R
P
by
the divider ratio. As an example, R
P
is about four milliohms
per foot with 16-gauge wire. This translates to 4mV per foot
at 1A load current. At higher load currents, this drop
represents a significant percentage of the overall regula-
tion. It is important to keep the positive lead between the
regulator and the load as short as possible and to use large
wire or PC board traces.
Figure 5. Connection for Best Load Regulation
LT1584
OUT
IN
V
IN
ADJ
R
PARASITIC
LINE RESISTANCE
R1*
*CONNECT R1 TO CASE
CONNECT R2 TO LOAD
LT1584 F05
R
L
R2*
Thermal Considerations
The LT1584/LT1585/LT1587 family protects the device
under overload conditions with internal power and thermal
limiting circuitry. However, for normal continuous load
conditions, do not exceed maximum junction temperature
ratings. It is important to consider all sources of thermal
resistance from junction-to-ambient. These sources in-
clude the junction-to-case resistance, the case-to-heat
sink interface resistance, and the heat sink resistance.
Thermal resistance specifications have been developed to
more accurately reflect device temperature and ensure safe
operating temperatures. The electrical characteristics sec-
tion provides a separate thermal resistance and maximum
junction temperature for both the control circuitry and the
power transistor. Older regulators, with a single junction-
to-case thermal resistance specification, use an average of
the two values provided here and allow excessive junction
temperatures under certain conditions of ambient tem-
perature and heat sink resistance. Calculate the maximum
junction temperature for both sections to ensure that both
thermal limits are met.
Junction-to-case thermal resistance is specified from the
IC junction to the bottom of the case directly below the die.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1584CT-3.3 | 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed |
| LT1584CT-3.38 | 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed |
| LT1584CT-3.45 | 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed |
| LT1584CT-3.6 | 7A, 4.6A, 3A Low Dropout Fast Response Positive Regulators Adjustable and Fixed |
| LT1587CM-1.5 | Fixed 1.5V, 3A Low Dropout Fast Response GTL + Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1584CT#32 | 制造商:Linear Technology 功能描述:ADJ L/DROPOUT HS 7A LINEAR REG |
| LT1584CT#PBF | 功能描述:IC REG LDO ADJ TO220-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT1584CT-3.3 | 功能描述:IC REG LDO 3.3V TO220-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:2.5 V ~ 5.5 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:300mA（最小值） 電流 - 限制（最?。?360mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 供應商設備封裝:TSOT-23-5 包裝:帶卷 (TR) |
| LT1584CT-3.3#PBF | 功能描述:IC REG LDO 3.3V TO220-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT1584CT-3.3#TRPBF | 制造商:Linear Technology 功能描述:LDO Regulator Pos 3.3V 7A 3-Pin(3+Tab) TO-220 T/R |
發布緊急采購，3分鐘左右您將得到回復。