- 您現在的位置：買賣IC網 > PDF目錄377709 > LT1618EMS (LINEAR TECHNOLOGY CORP) Constant-Current/ Constant-Voltage 1.4MHz Step-Up DC/DC Converter PDF資料下載
參數資料
| 型號： | LT1618EMS |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Constant-Current/ Constant-Voltage 1.4MHz Step-Up DC/DC Converter |
| 中文描述： | 2.8 A SWITCHING REGULATOR, 1600 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 202K |
| 代理商： | LT1618EMS |
LT1618
7
APPLICATIO
S I
FOR
ATIO
U
Setting Output Voltage
To set the output voltage, select the values of R1 and R2
(see Figure 1) according to the following equation.
W
U
U
R
R
V
OUT
1 263
.
1
2
1
=
–
For current source applications, use the FB pin for over-
voltage protection. Pick R1 and R2 so that the output
voltage will not go too high if the load is disconnected or
if the load current drops below the preset value. Typically
choose R1 and R2 so that the overvoltage value will be
about 20% to 30% higher than the normal output voltage
(when in constant-current mode). This prevents the volt-
age loop from interfering with the current loop in current
source applications. For battery charger applications, pick
the values of R1 and R2 to give the desired end of charge
voltage.
Selecting R
SENSE
/Current Sense Adjustment
Use the following formula to choose the correct current
sense resistor value (for constant current operation).
R
SENSE
= 50mV/I
MAX
For designs needing an adjustable current level, the I
ADJ
pin is provided. With the I
ADJ
pin tied to ground, the
nominal current sense voltage is 50mV (appearing be-
tween the ISP and ISN pins). Applying a positive DC
voltage to the I
ADJ
pin will decrease the current sense
voltage according to the following formula:
V
V
V
ISENSE
IADJ
=
1 263
0 8
25
.
– ( . )
For example, if 1V is applied to the I
ADJ
pin, the current
sense voltage will be reduced to about 18mV. This
adjustability allows the regulated current to be reduced
without changing the current sense resistor (e.g. to adjust
brightness in an LED driver or to reduce the charge current
in a battery charger). If the I
ADJ
pin is taken above 1.6V,
the output of the error amplifier (the V
C
pin) will be pulled
down and the LT1618 will stop switching.
A pulse width modulated (PWM) signal can also be used
to adjust the current sense voltage; simply add an RC
filterto convert the PWM signal into a DC voltage for the
I
ADJ
pin. If the I
ADJ
pin is not used, it should be tied to
ground. Do not leave the pin floating.
For applications needing only a simple one-step current
sense adjustment, the circuit in Figure 2 works well. If a
large value resistor (
≥
2M
) is placed between the I
ADJ
pin
and ground, the current sense voltage will reduce to about
25mV, providing a 50% reduction in current. Do not leave
the I
ADJ
pin open. This method gives a well-regulated
current value in both states, and is controlled by a logic
signal without the need for a variable PWM or DC control
signal. When the NMOS transistor is on, the current sense
voltage will be 50mV, when it is off, the current sense
voltage will be reduced to 25mV.
Figure 2
LT1618
I
ADJ
2M
FULL
CURRENT
1618 F02
Considerations When Sensing Input Current
In addition to regulating the DC output current for current-
source applications, the constant-current loop of the
LT1618 can also be used to provide an accurate input
current limit. Boost converters cannot provide output
short-circuit protection, but the surge turn-on current can
be drastically reduced using the LT1618’s current sense
at the input. SEPICs, however, have an output that is DC-
isolated from the input, so an input current limit not only
helps soft-start the output but also provides excellent
short-circuit protection.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1618 | Constant-Current/ Constant-Voltage 1.4MHz Step-Up DC/DC Converter(恒定電流/恒定電壓，1.4MHz,步升DC/DC變換器) |
| LT1619 | Low Voltage Current Mode PWM Controller |
| LT1619ES8 | Low Voltage Current Mode PWM Controller |
| LT1619EMS8 | Low Voltage Current Mode PWM Controller |
| LT1620CS8 | Rail-to-Rail Current Sense Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1618EMS#PBF | 功能描述:IC REG BOOST ADJ 1.5A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT1618EMS#TR | 功能描述:IC REG BOOST ADJ 1.5A 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1618EMS#TRPBF | 功能描述:IC REG BOOST ADJ 1.5A 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT1618EMSPBF | 制造商: 功能描述: 制造商:Linear Technology 功能描述:DC-DC Converter 1.4MHz Step-Up MSOP10 |
| LT1619 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:2-Phase Step-Up DC/DC Controller |
發布緊急采購，3分鐘左右您將得到回復。