參數資料
型號： LT1619
廠商： Linear Technology Corporation
英文描述： Low Voltage Current Mode PWM Controller
中文描述： 低電壓電流模式PWM控制器
文件頁數： 6/20頁
文件大?。?/td> 256K
代理商： LT1619
6
LT1619
1619fa
The LT1619 is a fixed frequency current mode switching
regulator PWM controller that can be used in boost, SEPIC
or flyback modes. The device operates from an input
supply range of 1.9V to 18V, and has a separate supply pin
(DRV) for the gate driver. The DRV pin can be bootstrapped
to V
OUT
for additional gate enhancement in low voltage
applications like 3.3V to 5V boost converters, or con-
nected to the input supply for higher voltage inputs.
To best understand operation of the LT1619, please refer
to Figure 2, the Block Diagram. The gate drive circuit turns
on the external MOSFET at the trailing edge of oscillator
output signal CLK. MOSFET current is sensed with an
external resistor (R
SENSE
of Figure 1). A leading edge
blanking circuit disables the current sense amplifier for
280ns immediately following switch turn-on, preventing
gate charging current from prematurely tripping the PWM
comparator. A slope compensating ramp, derived from
the oscillator, is added to the current sense output. The
driver turns off the MOSFET when this sum exceeds the
error amplifier output V
C
. The switch current is limited
with a separate comparator. The compensating ramp is a
progressive nonlinear function of the operating duty ratio
whereas the current limit does not vary with the duty ratio.
Error amplifier output V
C
determines the peak switch cur-
rent required to regulate the output voltage. V
C
can be
considered a measure of output current. At heavy loads,
V
C
is in its upper range. Average and peak inductor cur-
rents are high. In this range, the inductor tends to run in
continuous conduction mode (CCM), where current is al-
ways flowing in the inductor. As load current decreases,
average and peak inductor current decreases. When the
average inductor current falls below 1/2 of the peak-to-peak
inductor current ripple, the converter enters discontinu-
ous conduction mode (DCM), where current in the induc-
tor reaches zero sometime during the discharge phase.
Further reduction in output current moves V
C
towards its
lower operating range, decreasing inductor current. Hys-
teretic comparator A1 determines if V
C
is too low for the
LT1619 to operate efficiently. As V
C
falls below the trip
voltage VB, A1’s output goes high, turning off all blocks
except the error amplifier, A1 and A2. The LT1619 enters
the idle state and switching stops. The device draws just
140
μ
A from the input in the idle state. Output load current
discharges the output capacitor, causing the output volt-
age to decrease. As V
OUT
decreases, V
C
increases. As V
C
increases above V
B
, switching action begins, delivering
power to the output. The switch current sense threshold is
about 10mV in this V
C
region. If the output load remains
light, the output voltage will rise and V
C
will fall, causing
the converter to idle again. This is known as Burst Mode
operation. The burst frequency depends on input voltage,
output voltage, inductance and output capacitance. Out-
put voltage ripple during Burst Mode operation is usually
higher than when the converter is switching continuously.
Burst Mode operation increases light load efficiency be-
cause it delivers more energy per clock cycle than possible
with discontinuous mode operation and extremely low
peak switch current, allowing fewer switching cycles to
maintain a given output. IC supply current therefore be-
comes a small fraction of the total input current.
Setting Output Voltage
The output voltage of the LT1619 is set with resistive
divider R1 and R2 connected from the output to ground as
detailed in Figure 3. The divider tap is tied to the device FB
pin. Current through R2 should be significantly higher
than the FB pin bias current of 25nA. With R2 = 10k, the
input bias current of the error amplifier is 0.02% of the
current in R2.
Figure 3. Feedback Resistive Divider
Synchronization and Shutdown
The S/S pin (Pin 1) can be used to synchronize the
oscillator to an external source. The S/S pin is tied to the
input (V
IN
> 1.9V) for normal operation. The oscillator in
the LT1619 can be externally synchronized by driving the
S/S pin with a pulse train with an amplitude of at least 1V.
The maximum allowable rise time is a function of the
pulse amplitude, as shown in Table 1. Rise times equal to
OPERATIOU
V
O
R1
R1
R2
V
O
= 1.24V 1 +
R1 = R2
(
– 1
R2
1619 F03
(
)
V
O
1.24
)
LT1619
FB
相關PDF資料
PDF描述
LT1619ES8 Low Voltage Current Mode PWM Controller
LT1619EMS8 Low Voltage Current Mode PWM Controller
LT1620CS8 Rail-to-Rail Current Sense Amplifier
LT1620IGN CAP 0.1UF 200V 10% X7R SMD-1206 TR-7 PLATED-NI/SN
LT1621IGN Rail-to-Rail Current Sense Amplifier
相關代理商/技術參數
參數描述
LT1619EMS8 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LT1619EMS8#PBF 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR
LT1619EMS8#TR 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LT1619EMS8#TRPBF 功能描述:IC REG CTRLR PWM CM 8-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR)
LT1619EMS8PBF 制造商:Linear Technology 功能描述:PWM Controller Current Mode 1.5A MSOP8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*