- 您現在的位置：買賣IC網 > PDF目錄30766 > LT1621IGN#TR (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO16 PDF資料下載
參數資料
| 型號： | LT1621IGN#TR |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 242K |
| 代理商： | LT1621IGN#TR |
8
LT1620/LT1621
APPLICATIONS INFORMATION
WU
U
reduces battery charging current until the external load
subsides.
In Figure 4 the LT1620 is coupled with an LT1513 SEPIC
battery charger IC to create an input overcurrent protected
charger circuit.
The programming voltage (VCC – VPROG) is set to 1.0V
through a resistor divider (RP1 and RP2) from the 5V input
supply to ground. In this configuration, if the input current
drawn by the battery charger
combined with the system
load requirements exceeds a current limit threshold of 3A,
the battery charger current will be reduced by the LT1620
such that the total
input supply current is limited to 3A.
Refer to the LT1513 data sheet for additional information.
PROGRAMMING ACCURACY CONSIDERATIONS
PWM Controller Error Amp Maximum Source Current
In a typical battery charger application, the LT1620 con-
trols charge current by servoing the error amplifier output
pin of the associated PWM controller IC. Current mode
control is achieved when the LT1620 sinks all of the
current available from the error amplifier. Since the LT1620
has finite transconductance, the voltage required to gen-
erate its necessary output current translates to input
offset error. The LT1620 is designed for a typical IOUT sink
current of 130
A to help reduce this term. Knowing the
current source capability of the associated PWM control-
ler in a given application will enable adjustment of the
required programming voltage to accommodate the de-
sired charge current. A plot of typical VPROG voltage offset
vs PWM source capability is shown in Figure 5a. For
example, the LTC1435 has a current source capability of
about 75
A. This translates to about –15mV of induced
programming offset at VPROG (the absolute voltage at the
PROG pin must be 15mV lower).
VCC – VPROG Programmed Voltage ≠ 0.8V
The LT1620 sense amplifier circuit has an inherent input
referred 3mV offset when IN+ – IN– = 0V to insure closed-
loop operation during light load conditions. This offset vs
input voltage has a linear characteristic, crossing 0V as
IN+ – IN– = 80mV. The offset is translated to the AVG
output (times a factor of 10), and thus to the programming
voltage VPROG. A plot of typical VPROG offset voltage vs
IN+ – IN– is pictured in Figure 5b. For example, if the
desired load current corresponds to 100mV across the
sense resistor, the typical offset, at VPROG is 7.5mV (the
absolute voltage at the PROG pin must be 7.5mV higher).
This error term should be taken into consideration when
using VID values significantly away from 80mV.
VCC – VPROG2 Programmed Voltage ≠ 1.6V
(LT1620GN Only)
The offset term described above for VPROG also affects the
VPROG2 programming voltage proportionally (times an addi-
tional factor of 2). However, VPROG2 voltage is typically set
well below the zero offset point of 1.6V, so adjustment for this
term is usually required. A plot of typical VPROG2 offset
voltage vs IN+ – IN– is pictured in Figure 5c. For example,
setting the VPROG2 voltage to correspond to IN+ – IN–= 15mV
typically requires an additional –50mV offset (the absolute
voltage at the PROG2 pin must be 50mV lower).
Sense Amplifier Input Common Mode < (VCC – 0.5V)
The LT1620 sense amplifier has additional input offset
tolerance when the inputs are pulled significantly below
the VCC supply. The amplifier can induce additional input
referred offset of up to 11mV when the inputs are at 0V
common-mode. This additional offset term reduces roughly
linearly to zero when VCM is about VCC – 0.5V. In typical
applications, this offset increases the charge current tol-
erance for “cold start” conditions until VBAT moves away
from ground. The resulting output current shift is generally
negative; however, this offset is not precisely controlled.
Precision operation should not be attempted with sense
amplifier common mode inputs below VCC – 0.5V. Input
referred offset tolerance vs VCM is shown in Figure 5d.
VCC ≠ 5V
The LT1620 sense amplifier induces a small additional
offset when VCC moves away from 5V. This offset follows
a linear characteristic and amounts to about
±0.33mV
(input-referred) over the recommended operating range
of VCC, centered at 5V. This offset is translated to the AVG
and AVG2 outputs (times factors of 10 and 20), and thus
to the programming voltages. A plot of programming
offsets vs VCC is shown in Figure 5e.
相關PDF資料 |
PDF描述 |
|---|---|
| LT1620CS8#TR | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| LT1620IGN#TR | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| LT1740-7DZB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LT1840-7DZB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
| LT1240-7DZB1 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1624IS8 | 制造商:Linear Technology 功能描述: |
| LT-1625S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:T1/CEPT/ISDN-PRI TRANSFORMER |
| LT1627 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Low Dropout Regulators with Shutdown |
| LT1629 | 制造商:EDSYN 功能描述: |
| LT1630 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:30MHz, 10V/us, Dual/Quad Rail-to-Rail Input and Output Precision Op Amps |
發布緊急采購，3分鐘左右您將得到回復。