- 您現在的位置：買賣IC網 > PDF目錄10682 > LT1715CMS (Linear Technology)IC COMPARATOR 150MHZ DUAL 10MSOP PDF資料下載
參數資料
| 型號： | LT1715CMS |
| 廠商： | Linear Technology |
| 文件頁數： | 20/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMPARATOR 150MHZ DUAL 10MSOP |
| 標準包裝： | 50 |
| 系列： | UltraFast™ |
| 類型： | 通用 |
| 元件數： | 2 |
| 輸出類型： | CMOS，滿擺幅，TTL |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 12 V |
| 電壓 - 輸入偏移（最小值）： | 2.5mV @ ±5V |
| 電流 - 輸入偏壓（最小值）： | 6µA @ ±5V |
| 電流 - 輸出（標準）： | 20mA |
| 電流 - 靜態（最大值）： | 2mA |
| CMRR, PSRR（標準）： | 70dB CMRR，80dB PSRR |
| 傳輸延遲（最大）： | 9ns |
| 磁滯： | 6mV |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 安裝類型： | 表面貼裝 |
| 包裝： | 管件 |
LT1715
9
1715fa
Power Supply Congurations
The LT1715 has separate supply pins for the input and
output stages that allow exible operation, accommodating
separate voltage ranges for the analog input and the output
logic. Of course, a single 3V/5V supply may be used by
tying +VS and VCC together as well as GND and VEE.
The minimum voltage requirement can be simply stated
as both the output and the input stages need at least 2.7V
and the VEE pin must be equal to or less than ground.
The following rules must be adhered to in any conguration:
2.7V ≤ (VCC – VEE) ≤ 12V
2.7V ≤ (+VS – GND) ≤ 6V
(+VS – VEE)) ≤ 12V
VEE ≤ Ground
Although the ground pin need not be tied to system ground,
most applications will use it that way. Figure 1 shows three
common congurations. The nal one is uncommon, but
it will work and may be useful as a level translator; the
input stage is run from –5.2V and ground while the output
stage is run from 3V and ground. In this case the com-
mon mode input voltage range does not include ground,
so it may be helpful to tie VCC to 3V. Conversely, VCC may
also be tied below ground, as long as the above rules are
not violated.
Input Voltage Considerations
The LT1715 is specied for a common mode range of
–100mV to 3.8V when used with a single 5V supply. A
more general consideration is that the common mode
range is 100mV below VEE to 1.2V below VCC. The crite-
rion for this common mode limit is that the output still
responds correctly to a small differential input signal. If
one input is within the common mode limit, the other
input signal can go outside the common mode limits, up
to the absolute maximum limits, and the output will retain
the correct polarity.
When either input signal falls below the negative common
mode limit, the internal PN diode formed with the substrate
can turn on, resulting in signicant current ow through
the die. An external Schottky clamp diode between the
input and the negative rail can speed uprecovery from
negative overdrive by preventing the substrate diode from
turning on.
When both input signals are below the negative common
mode limit, phase reversal protection circuitry prevents
false output inversion to at least –400mV common mode.
However, the offset and hysteresis in this mode will increase
dramatically, to as much as 15mV each. The input bias
currents will also increase.
When one input signal goes above the common mode range
without exceeding a diode drop above the input supply rail,
the input stage will remain biased and the comparator will
maintain correct output polarity. Above this voltage, the
input stage current source will saturate completely and
the ESD protection diode will forward conduct. Once the
aberrant input falls back into the common mode range,
the comparator will respond correctly to valid input signals
within less than 10ns.
Figure 1. Variety of Power Supply Congurations
–
+
VEE
VCC
2.7V TO 6V
+VS
GND
Single Supply
–
+
VEE
VCC
5V
–5V
3V
+VS
GND
±5V Input, 3V Output Supplies
–
+
VEE
VCC
12V
5V
+VS
GND
12V Input, 5V Output Supplies
–
+
VEE
VCC
–5.2V
3V
+VS
GND
1715 F01
Front End Entirely Negative
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2V4-IX-B1 | CONVERTER MOD DC/DC 48V 75W |
| LTC1863CGN#PBF | IC ADC 12BIT 8CH 200KSPS 16SSOP |
| VE-2V3-IX-B1 | CONVERTER MOD DC/DC 24V 75W |
| LT1720IS8#TR | IC COMP DUAL R-R 4MA 4.5NS 8SOIC |
| LTC2431CMS#PBF | IC ADC 20BIT DIFFINPUT/REF10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1715CMS#PBF | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 類型:帶電壓基準 元件數:4 輸出類型:開路漏極 電壓 - 電源，單路/雙路(±):2.5 V ~ 11 V，±1.25 V ~ 5.5 V 電壓 - 輸入偏移（最小值）:10mV @ 5V 電流 - 輸入偏壓（最小值）:- 電流 - 輸出（標準）:0.015mA @ 5V 電流 - 靜態（最大值）:8.5µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:- 磁滯:- 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 安裝類型:表面貼裝 包裝:管件 產品目錄頁面:1386 (CN2011-ZH PDF) |
| LT1715CMS#PBF | 制造商:Linear Technology 功能描述:High Speed Comparator IC |
| LT1715CMS#PBF | 制造商:Linear Technology 功能描述:IC HIGH SPEED COMPARATOR |
| LT1715CMS#TR | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:否 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
| LT1715CMS#TRPBF | 功能描述:IC COMPARATOR 150MHZ DUAL 10MSOP RoHS:是 類別:集成電路 (IC) >> 線性 - 比較器 系列:UltraFast™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:通用 元件數:1 輸出類型:CMOS，推挽式，滿擺幅，TTL 電壓 - 電源，單路/雙路(±):2.5 V ~ 5.5 V，±1.25 V ~ 2.75 V 電壓 - 輸入偏移（最小值）:5mV @ 5.5V 電流 - 輸入偏壓（最小值）:1pA @ 5.5V 電流 - 輸出（標準）:- 電流 - 靜態（最大值）:24µA CMRR, PSRR（標準）:80dB CMRR，80dB PSRR 傳輸延遲（最大）:450ns 磁滯:±3mV 工作溫度:-40°C ~ 85°C 封裝/外殼:6-WFBGA，CSPBGA 安裝類型:表面貼裝 包裝:管件 其它名稱:Q3554586 |
發布緊急采購，3分鐘左右您將得到回復。