參數資料
型號: LT1970IFE#TRPBF
廠商: Linear Technology
文件頁數: 14/26頁
文件大小: 0K
描述: IC OP AMP 500MA ADJ 20-TSSOP
標準包裝: 2,500
放大器類型: 通用
電路數: 1
轉換速率: 1.6 V/µs
增益帶寬積: 3.6MHz
電流 - 輸入偏壓: 160nA
電壓 - 輸入偏移: 200µV
電流 - 電源: 7mA
電流 - 輸出 / 通道: 800mA
電壓 - 電源,單路/雙路(±): 5 V ~ 36 V,±2.5 V ~ 18 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)裸露焊盤
供應商設備封裝: 20-TSSOP-EP
包裝: 帶卷 (TR)
LT1970
21
1970fc
APPLICATIONS INFORMATION
range all the way to 0V, an LTC1046 charge pump inverter
is used to develop a –5V supply. This produces a negative
rail for the LT1970 which has to sink only the quiescent
current of the amplier, typically 7mA.
Using a second LT1970, a 0V to ±12V dual tracking power
supply is shown in Figure 12. The midpoint of two 10k
resistors connected between the + and – outputs is held
at 0V by the LT1881 dual op amp servo feedback loop. To
maintain 0V, both outputs must be equal and opposite in
polarity, thus they track each other. If one output reaches
current limit and drops in voltage, the other output fol-
lows to maintain a symmetrical + and – voltage across a
common load. Again, the output current limit is less than
the full capability of the LT1970 due to thermal reasons.
Separate current limit indicators are used on each LT1970
because one output only sources current and the other
only sinks current. Both devices can share the same
thermal shutdown indicator, as the output ags can be
OR’ed together.
Another simple linear power amplier circuit is shown in
Figure 13. This uses the LT1970 as a linear driver of a DC
motor with speed control. The ability to source and sink
the same amount of output current provides for bidirec-
tional rotation of the motor. Speed control is managed by
sensing the output of a tachometer built on to the motor.
A typical feedback signal of 3V/1000rpm is compared
with the desired speed-set input voltage. Because the
LT1970 is unity-gain stable, it can be congured as an
integrator to force whatever voltage across the motor as
necessary to match the feedback speed signal with the
set input signal.
Additionally, the current limit of the amplier can be ad-
justed to control the torque and stall current of the motor.
For reliability, a feedback scheme similar to that shown in
Figure 4 can be used. Assuming that a stalled rotor will
generate a current limit condition, the stall current limit
can be signicantly reduced to prevent excessive power
dissipation in the motor windings.
Figure 13. Simple Bidirectional DC Motor Speed Controller
VCSRC
COMMON
R4
49.9k
15V
–15V
REVERSE
FORWARD
R2
10k
VEE
VCSNK
V
FILTER
V+
15V
EN
VCC
ISNK
ISRC
SENSE
SENSE+
TSD
OUT
+IN
LT1970
–15V
–IN
RS
12V DC
MOTOR
TACH
FEEDBACK
3V/1000rpm
GND
1970 F13
C1
1μF
R5
49.9k
R3
1.2k
R1
1.2k
OV TO 5V
TORQUE/STALL
CURRENT CONTROL
相關PDF資料
PDF描述
LT1990AHS8#TRPBF IC AMP DIFF +/-250V MCRPWR 8SOIC
LT1993CUD-10#TRPBF IC DIFF AMP/ADC DRVR 16-QFN
LT1993CUD-2#PBF IC DIFF AMP/ADC DRVR 16-QFN
LT1993CUD-4#TRPBF IC DIFF AMP/ADC DRVR 16-QFN
LT1994MPDD#TRPBF IC DIFF AMP/DRIVER LN 8-MSOP
相關代理商/技術參數
參數描述
LT1976 制造商:LINER 制造商全稱:Linear Technology 功能描述:Monolithic Dual Tracking 3A Step-Down Switching
LT1976B 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage 1.5A, 200kHz Step-Down Switching Regulator with 100μA Quiescent Current
LT1976BEFE 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 2.4V to 60V 16-Pin TSSOP EP
LT1976BEFE#PBF 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V,1.5V,1.8V,2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬)裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤
LT1976BEFE#TRPBF 功能描述:IC REG BUCK ADJ 1.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:降壓(降壓) 輸出類型:固定 輸出數:1 輸出電壓:1.2V,1.5V,1.8V,2.5V 輸入電壓:2.7 V ~ 20 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:50mA 同步整流器:是 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬)裸露焊盤 包裝:帶卷 (TR) 供應商設備封裝:10-MSOP 裸露焊盤