參數資料
型號: LT1993IUD-10#PBF
廠商: Linear Technology
文件頁數: 3/16頁
文件大小: 0K
描述: IC DIFF AMP/ADC DRVR 16-QFN
標準包裝: 121
放大器類型: 差分
電路數: 2
輸出類型: 差分
轉換速率: 1100 V/µs
-3db帶寬: 700MHz
電流 - 輸入偏壓: 5µA
電壓 - 輸入偏移: 1000µV
電流 - 電源: 100mA
電流 - 輸出 / 通道: 45mA
電壓 - 電源,單路/雙路(±): 4 V ~ 5.5 V,±2 V ~ 2.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 16-WFQFN 裸露焊盤
供應商設備封裝: 16-QFN-EP(3x3)
包裝: 管件
LT1993-10
11
199310fb
APPLICATIO S I FOR ATIO
WU
U
Circuit Description
The LT1993-10 is a low noise, low distortion differential
amplier/ADC driver with:
DC to 700MHz –3dB bandwidth
Fixed gain of 10V/V (20dB) independent of RLOAD
100
Ω differential input impedance
Low output impedance
Built-in, user adjustable output ltering
Requires minimal support circuitry
Referring to the block diagram, the LT1993-10 uses a
closed-loop topology which incorporates 3 internal am-
pliers. Two of the ampliers (A and B) are identical and
drive the differential outputs. The third amplier (C) is
used to set the output common mode voltage. Gain and
input impedance are set by the 100
Ω/500Ω resistors in
the internal feedback network. Output impedance is low,
determined by the inherent output impedance of ampliers
A and B, and further reduced by internal feedback.
The LT1993-10 also includes built-in single-pole output
ltering. The user has the choice of using the unltered
outputs, the ltered outputs (175MHz –3dB lowpass), or
modifying the ltered outputs to alter frequency response
by adding additional components. Many lowpass and
bandpass lters are easily implemented with just one or
two additional components.
The LT1993-10 has been designed to minimize the need
for external support components such as transformers or
AC-coupling capacitors. As an ADC driver, the LT1993-10
requires no external components except for power-supply
bypass capacitors. This allows DC-coupled operation for
applications that have frequency ranges including DC. At
the outputs, the common mode voltage is set via the VOCM
pin, allowing the LT1993-10 to drive ADCs directly. No
output AC-coupling capacitors or transformers are needed.
At the inputs, signals can be differential or single-ended
with virtually no difference in performance. Furthermore,
DC levels at the inputs can be set independently of the
output common mode voltage. These input characteristics
often eliminate the need for an input transformer and/or
AC-coupling capacitors.
Input Impedance and Matching Networks
Because of the internal feedback network, calculation of
the LT1993-10’s input impedance is not straightforward
from examination of the block diagram. Furthermore, the
input impedance when driven differentially is different than
when driven single-ended. When driven differentially, the
LT1993-10’s input impedance is 100
Ω (differential); when
driven single-ended, the input impedance is 85.9
Ω.
For single-ended 50
Ω applications, a 121Ω shunt match-
ing resistor to ground will result in the proper input
termination (Figure 1). For differential inputs there are
several termination options. If the input source is 50
Ω
differential, then input matching can be accomplished by
either a 100
Ω shunt resistor across the inputs (Figure 3),
or a 49.9
Ω shunt resistor on each of the inputs to ground
(Figure 2).
199310 F01
IF IN
0.1
mF
LT1993-10
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
121
W
ZIN = 50W
SINGLE-ENDED
16
Figure 1. Input Termination for Single-Ended 50
Ω
Input Impedance
Figure 2. Input Termination for Differential 50
Ω Input Impedance
199310 F02
IF IN
IF IN+
LT1993-10
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
49.9
9
ZIN = 509
DIFFERENTIAL
16
49.9
9
Figure 3. Alternate Input Termination for Differential
50
Ω Input Impedance
199310 F03
IF IN
IF IN+
LT1993-10
–INA
–INB
–OUT
+OUT
8
5
+INB
+INA
14
13
15
ZIN = 509
DIFFERENTIAL
16
100
9
相關PDF資料
PDF描述
SL1021B300RF GAS TUBE 300V HVY 10KA 3PIN RADL
SL1021B260RF GAS TUBE 260V HVY 10KA 3PIN RADL
SL1021B250RF GAS TUBE 250V HVY 10KA 3PIN RADL
RC0805FR-072R8L RES 2.80 OHM 1/8W 1% 0805 SMD
SL1021B230RF GAS TUBE 230V HVY 10KA 3PIN RADL
相關代理商/技術參數
參數描述
LT1993IUD-2 制造商:Linear Technology 功能描述:SP Amp DIFF AMP Single 5.5V 16-Pin QFN EP
LT1993IUD-2#PBF 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 12 V,±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT
LT1993IUD-2#TRPBF 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:73 系列:Over-The-Top® 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.07 V/µs 增益帶寬積:200kHz -3db帶寬:- 電流 - 輸入偏壓:1nA 電壓 - 輸入偏移:285µV 電流 - 電源:50µA 電流 - 輸出 / 通道:25mA 電壓 - 電源,單路/雙路(±):2 V ~ 44 V,±1 V ~ 22 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-WFDFN 裸露焊盤 供應商設備封裝:16-DFN-EP(5x3) 包裝:管件
LT1993IUD-4 制造商:Linear Technology 功能描述:SC-Amps/High Speed, 900MHz Low Noise/Distortion Differential Amplifer 制造商:Linear Technology 功能描述:IC,Differential Amplifier,SINGLE,LLCC,16PIN,PLASTIC , RoHS Compliant: No
LT1993IUD-4#PBF 功能描述:IC DIFF AMP/ADC DRVR 16-QFN RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.028 V/µs 增益帶寬積:105kHz -3db帶寬:- 電流 - 輸入偏壓:3nA 電壓 - 輸入偏移:100µV 電流 - 電源:3.3µA 電流 - 輸出 / 通道:12mA 電壓 - 電源,單路/雙路(±):2.7 V ~ 12 V,±1.35 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:14-TSSOP 包裝:剪切帶 (CT) 其它名稱:OP481GRUZ-REELCT