參數資料
型號: LT3021ES8-1.8
廠商: LINEAR TECHNOLOGY CORP
元件分類: 基準電壓源/電流源
英文描述: 500mA, Low Voltage, Very Low Dropout Linear Regulator
中文描述: 1.8 V FIXED POSITIVE LDO REGULATOR, 0.285 V DROPOUT, PDSO8
封裝: 0.150 INCH, PLASTIC, SOP-8
文件頁數: 9/16頁
文件大?。?/td> 235K
代理商: LT3021ES8-1.8
9
LT3021/LT3021-1.2/
LT3021-1.5/LT3021-1.8
3021fa
APPLICATIU
The LT3021 is a very low dropout linear regulator capable
of 1V input supply operation. Devices supply 500mA of
output current and dropout voltage is typically 155mV.
Quiescent current is typically 120
μ
A and drops to 3
μ
A in
shutdown. The LT3021 incorporates several protection
features, making it ideal for use in battery-powered sys-
tems. The device protects itself against reverse-input and
reverse-output voltages. In battery backup applications
where the output is held up by a backup battery when the
input is pulled to ground, the LT3021 acts as if a diode is
in series with its output which prevents reverse current
flow. In dual supply applications where the regulator load
is returned to a negative supply, the output can be pulled
below ground by as much as 10V without affecting start-
up or normal operation.
W
U
U
Adjustable Operation
The LT3021’s output voltage range is 0.2V to 9.5V. Figure
1 shows that the output voltage is set by the ratio of two
external resistors. The device regulates the output to
maintain the ADJ pin voltage at 200mV referenced to
ground. The current in R1 equals 200mV/R1 and the
current in R2 is the current in R1 minus the ADJ pin bias
current. The ADJ pin bias current of 20nA flows out of the
pin. Use the formula in Figure 1 to calculate output voltage.
An R1 value of 20k sets the resistor divider current to
10
μ
A. Note that in shutdown the output is turned off and
the divider current is zero. Curves of ADJ Pin Voltage vs
Temperature and ADJ Pin Bias Current vs Temperature
appear in the Typical Performance Characteristics section.
0.4mV at V
ADJ
= 200mV. At V
OUT
= 1.5V, load regulation is:
(1.5V/200mV) (0.4mV) = 3mV
Output Capacitance and Transient Response
The LT3021’s design is stable with a wide range of output
capacitors, but is optimized for low ESR ceramic capaci-
tors. The output capacitor’s ESR affects stability, most
notably with small value capacitors. Use a minimum
output capacitor of 3.3
μ
F with an ESR of 0.2
or less to
prevent oscillations. The LT3021 is a low voltage device,
and output load transient response is a function of output
capacitance. Larger values of output capacitance decrease
the peak deviations and provide improved transient re-
sponse for larger load current changes. For output capaci-
tor values greater than 22
μ
F a small feedforward capacitor
with a value of 300pF across the upper divider resistor (R2
in Figure 1) is required. Under extremely low output
current conditions (I
LOAD
< 30
μ
A) a low frequency small
signal oscillation (200Hz/8mV
P-P
at 1.2V output) can
occur. A minimum load of 100
μ
A is recommended to
prevent this instability.
Give extra consideration to the use of ceramic capacitors.
Manufacturers make ceramic capacitors with a variety of
dielectrics, each with a different behavior across tempera-
ture and applied voltage. The most common dielectrics are
Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics
provide high C-V products in a small package at low cost,
but exhibit strong voltage and temperature coefficients.
The X5R and X7R dielectrics yield highly stable
characterisitics and are more suitable for use as the output
capacitor at fractionally increased cost. The X5R and X7R
dielectrics both exhibit excellent voltage coefficient char-
acteristics. The X7R type works over a larger temperature
range and exhibits better temperature stability whereas
X5R is less expensive and is available in higher values.
Figures 2 and 3 show voltage coefficient and temperature
coefficient comparisons between Y5V and X5R material.
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress, simi-
lar to the way a piezoelectric accelerometer or microphone
works. For a ceramic capacitor, the stress can be induced
by vibrations in the system or thermal transients. The re-
sulting voltages produced can cause appreciable amounts
IN
SHDN
R2
R1
3021 F01
OUT
V
IN
ADJ
GND
LT3021
V
OUT
+
R2
R1
V
OUT
= 200mV
V
ADJ
= 200mV
I
ADJ
= 20nA AT 25
°
C
OUTPUT RANGE = 0.2V TO 9.5V
1 +
– I
ADJ
(R2)
(
)
Figure 1. Adjustable Operation
Specifications for output voltages greater than 200mV are
proportional to the ratio of desired output voltage to
200mV; (V
OUT
/200mV). For example, load regulation for
an output current change of 1mA to 500mA is typically
相關PDF資料
PDF描述
LTC3025 500mA, Low Voltage, Very Low Dropout Linear Regulator
LT3021 500mA, Low Voltage, Very Low Dropout Linear Regulator
LT3021-1.2 500mA, Low Voltage, Very Low Dropout Linear Regulator
LT3021-1.5 500mA, Low Voltage, Very Low Dropout Linear Regulator
LT3021-1.8 500mA, Low Voltage, Very Low Dropout Linear Regulator
相關代理商/技術參數
參數描述
LT3021ES8PBF 制造商:Linear Technology 功能描述:LDO Regulator Adj. 500mA 0.9-10V SOIC8
LT3021IS8-1.8#PBF 功能描述:IC REG LDO 1.8V .5A 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正,固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降(標準):0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制(最小):4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6,D²Pak(5 引線+接片),TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR
LT3021IS8-1.8#TRPBF 功能描述:IC REG LDO 1.8V .5A 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正,固定式 輸出電壓:3V 輸入電壓:2.3 V ~ 5.5 V 電壓 - 壓降(標準):0.035V @ 150mA 穩壓器數量:2 電流 - 輸出:150mA 電流 - 限制(最?。?300mA 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 裸露焊盤,6-TMLF? 供應商設備封裝:6-TMLF?(1.6x1.6) 包裝:Digi-Reel® 產品目錄頁面:1104 (CN2011-ZH PDF) 其它名稱:576-3018-6
LT3022 制造商:LINER 制造商全稱:Linear Technology 功能描述:1.5A, Low Noise, Negative Linear Regulator
LT3022EDHC 制造商:LINER 制造商全稱:Linear Technology 功能描述:1A, 0.9V to 10V, Very Low Dropout Linear Regulator