- 您現在的位置：買賣IC網 > PDF目錄377722 > LT3024 (Linear Technology Corporation) Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator PDF資料下載
參數資料
| 型號： | LT3024 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator |
| 中文描述： | 雙100mA/500mA低壓差，低噪聲，微功耗穩壓器 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 493K |
| 代理商： | LT3024 |
10
LT3024
3024f
SHDN1/SHDN2 (Pins 11/8)/(Pins 14/11):
Shutdown. The
SHDN1/SHDN2 pins are used to put the corresponding
output of the LT3024 regulator into a low power shutdown
state. The output will be off when the pin is pulled low. The
SHDN1/SHDN2 pins can be driven either by 5V logic or
open-collector logic with pull-up resistors. The pull-up
resistors are required to supply the pull-up current of the
open-collector gates, normally several microamperes,
and the SHDN1/SHDN2 pin current, typically 1
μ
A. If
unused, the pin must be connected to V
IN
. The device will
not function if the SHDN1/SHDN2 pins are not connected.
IN (Pins 9, 10)/(Pins 12, 13):
Input. Power is supplied to
the device through the IN pin. A bypass capacitor is
required on this pin if the device is more than six inches
away from the main input filter capacitor. In general, the
output impedance of a battery rises with frequency, so it
is advisable to include a bypass capacitor in battery-
powered circuits. A bypass capacitor in the range of 1
μ
F to
10
μ
F is sufficient. The LT3024 regulator is designed to
withstand reverse voltages on the IN pin with respect to
ground and the OUT pin. In the case of a reverse input,
which can happen if a battery is plugged in backwards, the
device will act as if there is a diode in series with its input.
There will be no reverse current flow into the regulator and
no reverse voltage will appear at the load. The device will
protect both itself and the load.
GND (Pins 4, 13)/(Pins 1, 5, 8, 9, 16, 17):
Ground. The
Exposed Pad must be soldered to PCB ground for opti-
mum thermal performance.
ADJ1/ADJ2 (Pins 12/7)/(Pins 15/10):
Adjust Pin. These
are the input to the error amplifiers. These pins are
internally clamped to
±
7V. They have a bias current of
30nA which flows into the pin (see curve of ADJ1/ADJ2 Pin
Bias Current vs Temperature in the Typical Performance
Characteristics section). The ADJ1 and ADJ2 pin voltage
is 1.22V referenced to ground and the output voltage
range is 1.22V to 20V.
BYP1/BYP2 (Pins 1/6)/(Pins 2/7):
Bypass. The BYP1/BYP2
pins are used to bypass the reference of the LT3024
regulator to achieve low noise performance from the
regulator. The BYP1/BYP2 pins are clamped internally to
±
0.6V (one V
BE
) from ground. A small capacitor from the
corresponding output to this pin will bypass the reference
to lower the output voltage noise. A maximum value of
0.01
μ
F can be used for reducing output voltage noise to a
typical 20
μ
V
RMS
over a 10Hz to 100kHz bandwidth. If not
used, this pin must be left unconnected.
OUT1/OUT2 (Pins 2, 3/5)/(Pins 3, 4/6):
Output. The
outputs supply power to the loads. A minimum output
capacitor of 1
μ
F is required to prevent oscillations on
Output 2; Output 1 requires a minimum of 3.3
μ
F. Larger
output capacitors will be required for applications with
large transient loads to limit peak voltage transients. See
the Applications Information section for more information
on output capacitance and reverse output characteristics.
PIU
(DFN Package)/(TSSOP Package)
APPLICATIOU
W
U
U
The LT3024 is a dual 100mA/500mA low dropout regula-
tor with micropower quiescent current and shutdown. The
device is capable of supplying 100mA from Output 2 at a
dropout voltage of 300mV. Output 1 delivers 500mA at a
dropout voltage of 300mV. The two regulators have com-
mon V
IN
and GND pins and are thermally coupled, how-
ever, the two outputs of the LT3024 operate indepen-
dently. They can be shut down independently and a fault
condition on one output will not affect the other output
electrically. Output voltage noise can be lowered to 20
μ
V
RMS
over a 10Hz to 100kHz bandwidth with the addition of a
0.01
μ
F reference bypass capacitor. Additionally, the refer-
ence bypass capacitor will improve transient response of
the regulator, lowering the settling time for transient load
conditions. The low operating quiescent current (30
μ
A per
output) drops to less than 1
μ
A in shutdown. In addition to
相關PDF資料 |
PDF描述 |
|---|---|
| LT3024EDE | Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator |
| LT3024EFE | Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator |
| LT311H | Voltage Comparator |
| LT311AN8 | Voltage Comparator |
| LT311 | Voltage Comparator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3024_1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 100mA/500mA Low Dropout, Low Noise,Micropower Regulator |
| LT3024EDE | 功能描述:IC REG LDO ADJ .5A/.1A 12DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT3024EDE#PBF | 功能描述:IC REG LDO ADJ .5A/.1A 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT3024EDE#TR | 功能描述:IC REG LDO ADJ .5A/.1A 12DFN RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT3024EDE#TRPBF | 功能描述:IC REG LDO ADJ .5A/.1A 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
發布緊急采購，3分鐘左右您將得到回復。